Operator’s Manual All specifications are subjected to change without notice SRP - 350 RECEIPT PRINTER
10 1-7. Adjustments and Settings The SRP-350 is set up at the factory to be appropriate for almost all users. It does, however, offer some setting
11 1-8. Using the Printer Control Panel Button The button can be disabled by the ESC c 5 command. Press the FEED button once to advance pa
12 Serial Interface(RS-232C, RS-485) Specification DIP Switch Set 1 Functions SW FUNCTION ON OFF DEFAULT 1 Data Receive Error Ignore Print ¡°?
13 Parallel/USB Interface Specification Dip Switch Set 1 Functions SW FUNCTION ON OFF DEFAULT 1 Reserved - - OFF 2 Reserved - - OFF 3 Re
14 Chapter 2. Hexadecimal Dumping This feature allows experienced users to see exactly what data is coming to the printer. This can be useful in find
15 Chapter 3. The self test The self-test checks whether the printer has any problems. If the printer does not function properly, contact your dealer
16 Chapter 4. Code Table The following pages show the character code tables. To find the character corresponding to a hexadecimal number, count acros
17 Page 2 ( PC850 : Multilingual )
18 Page 3 ( PC860 : Portuguese )
19 Page 4 ( PC 863 : Canadian - French )
2 Warning - U.S. This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules.
20 Page 5 ( PC 865 : Nordic )
21 Page 19 ( PC 858 : Euro )
22 Page 255 ( Space Page )
23 International Character Set
24 Chapter 5. Control Commands List Control codes Hexadecimal codes Function <HT> 09 Horizontal tab <LF> 0A Print and li
25 Control codes Hexadecimal codes Function <ESC> \ nL nH 1B 5C n Set relative print position <ESC> a n 1B 61 n Select j
26 Control codes Hexadecimal codes Function <GS> k m ….NUL <GS> k m n … 1D 6B m… NUL 1D 6B m n … Print bar code <GS> r
27 APPENDIX A. Star Mode Command Summary Control codes Hexadecimal codes Function <ESC> ”R” n 1B 52 n Select international
28 Control codes Hexadecimal codes Function <ESC> “I” n 1B 6C n Set left margin <ESC> “Q” n 1B 51 n Set right margin &
29 Control codes Hexadecimal codes Function <SUB> 1A Control peripheral device #2 immediately <ESC> “d” n 1B 64 n Part
3 Table of Contents CHAPTER 1. SETTING UP THE PRINTER...4 1-1. UNPACKING ...
30 B. Connectors SRP-350/SRP-350S Connector ( Serial Interface ) SRP-350P Connector ( Parallel Interface ) SRP-350U Connector ( USB Inter
31 Interface Connector Serial Interface(RS-232) Pin No. Signal name Direction Function 1 FG - Frame Ground 2 TxD Output Transmit Data 3 RxD I
32 Parallel Interface(IEEE-1284) Pin No. Source Compatibility Mode Nibble Mode Byte Mode 1 Host nStrobe HostClk HostClk 2 Host / Printer Data
33 USB Interface Pin No. Signal Name Assignment (Color) Function Shell Shield Drain Wire Frame Ground 1 VBUS Red Host Power 2 D- White
34 Drawer Connector Pin No. Signal name Direction 1 Frame ground - 2 Drawer kick- out drive signal 1 Output 3 Drawer open/close signal Input 4
35 D. Specification Printing method Thermal line printing Dot density 180 X 180 dpi (7dots/mm) Printing width 72.192 +0.2mm or –0.2mm Paper width
4 Chapter 1. Setting Up the Printer 1-1. Unpacking Your printer box should include these items. If any items are damaged or missing, please conta
5 1-2. Connecting the Cables You can connect up the three cables to the printer. They all connect to the connector panel on the back of the pr
6 1-3. Connecting the computer You need an appropriate interface cable. 1. Plug the cable connector securely into the printer’s interface connect
7 1-5. Connecting the Power Supply CAUTIONS: When connecting or disconnecting the power supply from the printer, make sure that the power su
8 1-6. Installing or Replacing the Paper Roll 1. Make sure that the printer is not receiving data; otherwise, data may be lost. 2. Open the paper
9 5. Be sure to note the correct direction that the paper comes off the roll. 6. Pull out a small amount of paper, as shown. Then close the c
Comments to this Manuals