Samsung RFG26MESL User Manual

This manual is made with 100% recycled paper.Refrigeratoruser manualimagine the possibilitiesThank you for purchasing a Samsung product.To receive a m

10_ setting upThe left door is fi xed. To make minor adjustments between doors, adjust only the right door.Pull out the Convertible door ( 1. 1 ) to ex

setting up _1101 SETTING UPCHECKING THE WATERA water dispenser with a fi lter is one of the helpful features on your new refrigerator. To help promote

12_ operatingTurn water on and check for any leakage. If you 4. fi nd water drops or leakage in the connection areas, turn off the main water supply. C

operating _1302 OPERATING( 1 ) Energy ( 1 ) Energy SaverSaverTouching this button turns Energy Saver mode on and off. When you turn Energy Saver on, t

14_ operating( 6 ) Ice Off ( 6 ) Ice Off (Hold 3 sec (Hold 3 sec for child for child lock)lock)If you don’t want to make more ice, touch this button.

operating _1502 OPERATINGCHANGING THE WATER FILTERTo reduce risk of water damage to your property, DO NOT use generic brands of water fi lters in your

16_ operatingand 120 psi (241 and 827 kPa).If a reverse osmosis water fi ltration system is connected to your cold water supply, the water pressure to

operating _1702 OPERATINGCrushed Ice feature, a small amount of residual crushed ice might be produced.After Water Dispenser Installation, press the •

18_ operatingDo not try to disassemble the ice maker. -Do not wash or spray the ice bucket with water -while it is in the refrigerator. Remove it to c

operating _1902 OPERATINGPARTS AND FEATURESUse this page to become more familiar with the parts and features of the refrigerator.When closing the door

02_ Safety informationsafety informationSAFETY INFORMATIONBefore operating the appliance, please read • this manual thoroughly and retain it at a safe

20_ operatingUSING FLEX ZONEThe Flex Zone is a full-width drawer with an adjustable temperature control. You can use the Flex Zone for large party tra

operating _2102 OPERATING2. Tempered Glass shelvesTo remove - Tilt up the front of the shelf in the direction shown ( 1 ) and lift it up vertically (

22_ operatingREMOVING THE FREEZER ACCESSORIES1. Freeze room GuardTo remove - Remove the freeze room guard ( 1 ) by lifting the guard up.To replace - P

operating _2302 OPERATINGDo not spray water directly on the refrigerator. Use a clean, damp cloth to clean.Do not use benzene, thinner, or Clorox for

24_ TroubleshootingTroubleshootingPROBLEM SOLUTIONThe refrigerator does not work at all or it does not chill suffi ciently.• Check that the power plug

memoDA68-02481C(EN)-0.5.indd 25DA68-02481C(EN)-0.5.indd 25 2012.5.25 10:38:39 AM2012.5.25 10:38:39 AM

memoDA68-02481C(EN)-0.5.indd 26DA68-02481C(EN)-0.5.indd 26 2012.5.25 10:38:39 AM2012.5.25 10:38:39 AM

memoDA68-02481C(EN)-0.5.indd 27DA68-02481C(EN)-0.5.indd 27 2012.5.25 10:38:39 AM2012.5.25 10:38:39 AM

Code No. DA68-02481C REV(0.5)Ambient Room Temperature LimitsThis refrigerator is designed to operate in ambient temperatures specifi ed by its temperat

Safety information _03(R600a), a natural gas with high environmental compatibility that is, however, also combustible. When transporting and installin

04_ Safety informationIt can cause death from suffocation by -entrapment or personal injury.Do not sit on the Freezer door.• The door may be broken a

Safety information _05freezing near to already existing food.Please observe maximum storage times and • expiry dates of frozen goods.Fill the water ta

06_ setting upis no need to manually defrost your appliance, as this will be carried out automatically.Temperature rise during defrosting can comply •

setting up _0701 SETTING UPDo not locate the refrigerator where it may • become wet.When moving your refrigeratorTo prevent fl oor damage, be sure the

08_ setting upDisconnect one connector ( 2. 3 ) on the right side door and one connector ( 4 ) on left side door. To remove the water coupler from the

setting up _0901 SETTING UPASSEMBLE THE FLEX DOORTo reattach the fl ex doors after you have moved the fridge to its fi nal location, assemble parts in r