Samsung SMM-15FDQ User Manual

COLOR DUAL QUAD OBSERVATION SYSYTEMSMM-15FDQ/21FDQUser GuideSMM-15FDQ/21FDQ_ENG_Cover 9/19/03 6:18 PM Page 1

11Chapter 3: Setting each item function at SETUP MENU3-1) ADJUST MENU function and setting method ... 333-2) DATE/TIME MENU Function

12Chapter 1: System Components and Installation1-1) Environmental requirements for installation and safety This section describes the environmental re

131-2) System ComponentsThe system consists of the following: • Check whether all the following devices and accessories are included with the main sys

15e. SENSOR jackUsed to connect the sensor to the camera.f. SpeakerIt outputs the sound signal which was transfered from the monitor.• PIN configurati

163) PIR Camera composition① LensIt has a focal length of 3.8mm and makes it possible for you to observe a relatively widearea.➁ SpeakerIt outputs the

17➃ 6-pin modular jackUsed to connect the camera to the monitor.⑤ 5-Pin Terminal BlockA terminal block for supplying backup power for the PIR sensor o

18(Sensor Detection Angle & Area)1) Vertical View Pattern2) Horizontal View Pattern

19➅ Function SwitchA function switch for the PIR sensor operation.⑦ PIR SensorA thermal heat sensor that detects infrared radiation projected by warm

2IMPORTANT SAFETY INSTRUCTIONS1. Read these instructions.2. Keep these Instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use this

20Camera installation Hints1. Do not install directly towards rising or setting sun. Can cause burn or damage to internal options.2. Do not limit de

214) Installing the PIR Camera (SMM-PIRCAM)1. Choose an installation site that can sufficiently support 5 times the weight of the equipments to bein

224. Connect the Camera connector(RJ-11) cable to the case-rear as well as the cable to be connected tothe terminal.5. Align the two holes of the cas

236. Adjust the direction of the lens.1) Use the cross (+) screw driver to turn the screw (indicated by the arrow in the illustration)counterclockwi

25•Loosen the handle by turning it in a counter clockwise direction and then adjust the camera position . Tighten the handle, turning it clockwise, an

261-4) CAMERA Composition and Connecting Method toMONITORAfter positioning monitor and installing four cameras to a desired location, please connect C

271-5) External terminal connecting method for CAMERA and MONITOR 1) External terminal connecting method for CAMERA •An additional PIR sensor or exter

28f) Connect the TRIGGER plug to the REC TRIGGER OUT terminal of the VCR.g) Connect the A/O (HOT) terminal on the rear panel to the Alarm IN terminal

29Chapter 2: MONITOR FRONT PANEL KEYFunction and Using MethodFront Panel 2-1) TALK KEYTALK KEY allows users to transmit voice signal to intended camer

Graphic Symbol ExplanationThe lightning flash with arrowhead symbol, within anequilateral triangle, is intended to alert the user to thepresence of un

302-4) POWER SAVE- KEYAllows users to set POWER SAVE MODE of monitor. PICTURE screen is off when the POWER SAVE KEY is pressed, and the ON/OFF status

312-8) PIP- KEYCan be used to see the main screen while Single screen is displayed. The main screen can be changedand transfered to another channel wh

322-13) ENTER- KEYAs a multi functional œœENTER√√ key, it allows users to 1. enter SET UP MENU movement andSETTING MODE and set data, and 2. display

33Chapter 3: Setting each item function at SETUPMENUPressing the MENU BUTTON of the FRONT PANEL allows users to enter SETUP MENU and see thefollowing

343-2) DATE/TIME MENU Function setting •Function: Sets the display date format and current time.•Setting method :Move to #2. DATE/TIME MENU by using

353-4) DISPLAY MENU function setting •Function: Allows users to select the color and ON/OFF of borderline at QUAD DISPLAY.•Setting method: Move to #

363-5) TITLE MENU Function setting •Function: Set the title of each camera at your discretion.•Setting method: Move to #5. TITLE MENU by using œœENT

373-6) ALARM MENU Function setting •Function: Allows users to set the ALARM MODE for each camera.•Setting method: Move to #6. ALARM MENU by using œ

3806/01/03 13:14:00NO CH MM/DD/YY HH:MM:SS EVT01 07 02/10/03 10:00:30 A02 01 02/11/03 11:22:00 L03 01 06/01/03 12:33:01 -04 02 06/01/03 13:01:03 -05

39Chapter 4: DISPLAY MODE setting method4-1) SINGLE SCREEN DISPLAY Initial display mode of monitor is QUAD A. In case users want to see the camera

4IMPORTANT SAFEGUARDSCautionPower source is indicated on the rear of the set. It contains high-voltage parts. If you remove the cover, it may cause fi

404-2) QUAD MODE DISPLAY Users can switch SINGLE DISPLAY MODE and SEQUENTIAL DISPLAY MODE to QUADDISPLAY MODE, or QUAD A (QUAD B) to QUAD B (QUAD A

414-3) AUTO SEQUENTIAL DISPLAY MODE Pressing on the SEQUENCE KEY on the front allows screen to automatically switch to SINGLEMODE full screen or QU

424-4) PIP MODE DISPLAY Can be used to see PIP screen in Single screen mode.If you press the œœENTER√√ on PIP screen ,the main screen will change.

434-5) ZOOM MODE DISPLAY When users want to see zoomed image of a specific area of the display, press the ZOOM KEY in thefront to display zoom sele

44Chapter 5: Each product featureSOD14C : Standard CameraModel Name Broadcasting System Imaging Device Effective Pixels Synchronization Resolution Sig

45Model Name Broadcasting System Imaging Device Effective PixelsSynchronization Resolution Signal Output S/N Ratio Minimum Scene IlluminationGamma Cor

46Model Name Broadcasting System Imaging Device Effective PixelsSynchronization ResolutionSignal Output S/N Ratio Minimum Scene Illumination Gamma Cor

47Video InputVideo OutputVoice InputVoice OutputAlarm/Motion Features:Connected to AlarmBox/CameraSequenceEvent ListDisplay modeHorizontal ResolutionO

Part No.: AA68-03176APrinted in KoreaSamsung CCTV dba GV11621 West Crosby, Suite 104Carrollton, TX. 75006PHONE : 866.492.8246SMM-15FDQ/21FDQ_ENG

Part No.: AA68-03176APrinted in KoreaSamsung CCTV dba GV11621 West Crosby, Suite 104Carrollton, TX. 75006PHONE : 866.492.8246SMM-15FDQ/21FDQ_ENG_Cover

58. Accessories : Do not place this monitor on an unstable cart, stand,tripod, bracket, or table. The monitor may fall, causing serious injury toa chi

613. Lightning : For added protection for this monitor during a lightningstorm, or when it is left unattended and unused for long periods of time,unpl

718. Replacement Parts : When replacement parts are required, be sure theservice technician has used replacement parts specified by Samsung orhave the

Information to userChanges or modifications not expressly approved by the party responsiblefor compliance could void the user's authority to oper

The party responsible for product compliance:SAMSUNG ELECTRONICS CO., LTD.America QA Lab of Samsung3351 Michelson Drive,Suite #290, Irvine, CA92612 US