Samsung AM060FXMDEH User Manual

AM✴✴✴XMDEH SeriesAM✴✴✴XMDGH SeriesAir Conditionerinstallation manualimagine the possibilitiesThank you for purchasing this Samsung product.DB68-03941A

10Installation locationMoving the Outdoor Unitf Select the moving route in advance.f Be sure that moving route is safe from the weight of the outdoo

11ENGLISHBase ground work< When installing on the ground >Drain hole 150mm or more< When installing on the roof >Install the outdoor unit

12Refrigerant pipe installationRefrigerant pipe work f The length of refrigerant pipe should be as short as possible and the height dierence between

13ENGLISHSelecting refrigerant pipe Temper grade and minimum thickness of the refrigerant pipeOuter diameter [mm] Minimum thickness [mm] Temper gradeø

14Refrigerant pipe installationSelecting Y-jointf Select the rst Y-joint according to main pipe size of each outdoor unit capacity.f Select the oth

15ENGLISHDirection of the pipe when brazingf Brazing the pipe should be done with the pipe headed downward or horizontally.f Avoid brazing with the

16Refrigerant pipe installationTightening are connection area f Check that the aring is properly made.f Align the center of the piping and sucien

17ENGLISHPipe installation for an outdoor unitPipe directionThe refrigerant pipe can be pulled out from front, ank, rear, and bottom side, so install

18Refrigerant pipe installationRefrigerant pipe installation examplesUsing a Y-joint Using a Y-joint/EEV kitUsing a header joint Using a header joint/

19ENGLISHClassication Y-joint connection Y-joint / EEV kit connectionMaximum allowable length of pipeOutdoor unit ~ Indoor unitsActual LengthThe dist

2ContentsSafety precautions ... 3Outdoor unit typ

20Refrigerant pipe installationConnection by header jointgOutdoor unitHeader jointIndoor unitConnection by Y-joint/header jointH2H1f cg Outdoor unitIn

21ENGLISHRefrigerant pipe workRefrigerant Y-joint installation Install the Y-joint ‘horizontally’ or ‘vertically’.f Install horizontallyf Install ve

22Refrigerant pipe installationCorrect use (The insertion depth of connecting pipe)Incorrect use(The insertion depth of connecting pipe)Basic specica

23ENGLISHt When using A~J type of header joint, connect the header joint to the pipe with provided reducer. t When using K~Z type of header joint, c

24Refrigerant pipe installationPerforming air tightening testf Use tools for R-410A only to prevent the inow of foreign substances and to resist the

25ENGLISHVacuuming a pipe and an indoor unitf Use the tools for R-410A only to prevent the inow of foreign substances and resist against the interna

26Refrigerant pipe installationSelecting additional refrigerant chargingf Basic refrigerantThe basic amount of additional refrigerant charged at a fa

27ENGLISH2. The amount of additional refrigerant for each indoor unit(Unit : kg)Capacity (kW)Model1.5 1.7 2.2 2.8 3.6 4.5 5.6 6 7.1 8.2 9 11.2 12.8 1

28Refrigerant pipe installationf Be sure to plug the rest of drain holes not connected with drain plugs using drain caps.Drain capDrain plugInsulatin

29ENGLISHInsulating refrigerant pipef You must insulate refrigerant pipe, Y-joint, header joint, and pipe connection area.f If you insulate the pipe

3ENGLISHSafety precautionsCarefully follow the precautions listed below because they are essential to guarantee the safety of the equipment.WARNINGt

30Refrigerant pipe installationInsulating the header jointf Fasten the header joint using a cable tie and cover the connected part.f Insulate the he

31ENGLISHWiring workf Wiring work should be performed in accordance with related laws such as ‘Technical specication on electric installation’, ‘Wir

32Wiring workOverall System CongurationConnection of the power cable (1 phase 2 wires)Distribution board Outdoor unit Indoor unitCommunication cable2

33ENGLISHConnection of the power cable (3 phase 4 wires)Distribution board Outdoor unit Indoor unitCommunication cable220VWired remote controllerEarth

34Wiring workSpecication for circuit breaker and power supply cordf Power supply cord is not supplied with air conditioner.f Select the power suppl

35ENGLISHSelecting compressed ring terminalf Select a compressed ring terminal of a connecting power cable based on a nominal dimensions for cable.f

36Wiring workInstalling grounding wiref Grounding must be done by a qualied installer for your safety.f Use the grounding wire by referring to the

37ENGLISHGrounding workIf the power distribution circuit does not have a grounding or the grounding does not comply with specications, a ground rod m

38Setting indoor unit option switch and key functionPBA shapeAM✴✴✴✴XMD✴H Series7-SEGMENT (DISPLAY)DIP S/W (K5~K16)Do not connect wires to these termin

39ENGLISHSetting the number of connecting indoor unitsEx : When you connect 3 indoor units, set SW02 to 3AM✴✴✴✴XMD✴H SeriesSW02Unit digitSW01Unit digi

4Safety precautionsInstalling the unitIMPORTANT: When installing the unit, always remember to connect rst the refrigerant tubes, then the electrical

40Setting indoor unit option switch and key functionDIP S/W specication settingAM✴✴✴✴XMD✴H SeriesTAC T switchNumber of pressesContent SEG1 SEG2 SEG3

41ENGLISHf K5 : Automatic / Manual Silent mode operation settingSwitchFunction (Silent mode operation control)K5ON Automatic Silent mode operationOFF

42Setting indoor unit option switch and key functionf K11, K12: Changing heating capacity correction tableSwitchFunctionK11 K12ON ON DefaultON OFF D

43ENGLISHf K15, K16: Defrost Option l This is to control entering condition of defrost modeSwitchFunctionK15 K16ON ON MIDON ON LOW1OFF OFF LOW2 ❋ Def

44Setting indoor unit option switch and key function ❋ While you are setting the option, you may press and hold the K1 button to reset the value to pr

45ENGLISHInspection before check operation1. Check the power cable and communication cable of the indoor and outdoor unit.2. Supply power to the out

46Inspection and check operationCheck operation1. Use KEY MODE to run check operation. - When the check operation is not completed, UP (unprepared) w

47ENGLISHCharging refrigerantRefrigerant type GWP valueR-410A 2088Unit kg tCO2e①, a②, b① + ②, ct GWP=Global Warming Potentialt Calculating tCOe : k

48Pump DownThe object of pump downf You can reduce as much refrigerant leakage as possible during product movement or repair by collecting the refrig

49ENGLISHHow to put the refrigerant into the refrigerant container before pump down operation ❋ When the amount of refrigerant charged in the system e

5ENGLISHOutdoor unit type ShapeModel Cooling and Heating1phaseAM040✴XMDEHAM050✴XMDEHAM060✴XMDEH 3phaseAM040✴XMDGHAM050✴XMDGHAM060✴XMDGH Installation

50Checking lists after nishing installationf Before supplying power, measure the power terminal (L, N) and outdoor unit grounding using insulation-r

51ENGLISHTrial operationf Check the power supply between the outdoor unit and the cabinet panel. - 1 phase power supply : L, N - 3 phase power suppl

6Deciding to where to install the outdoor unitDecide the installation location based on the following condition and obtain the user’s approval. f Avo

7ENGLISHt Install the indoor unit away from any interfering sources such as radio, computer, stereo equipment and also select a place where the elect

8Installation locationf Make a space for ventilation and service as seen in the picture.f When multiple outdoor units are combined for installation,

9ENGLISHWhen installing more than 1 outdoor unit ❋ When 3 sides of the outdoor unit are blocked by the wall (Unit : mm)300 or more300 or more 600 or m