Samsung SMO-120P User Manual

COLOR DUAL QUAD OBSERVATION SYSYTEMSMM-15FDQ/21FDQUser GuideManuel d'utilisationGuía del usuario

English-10ContentsIMPORTANT SAFETY INSTRUCTIONS ... 2IMPORTANT SAFEGUARDS...

Chapter 3: Setting each item function at SETUP MENU3-1) ADJUST MENU function and setting method ... 333-2) DATE/TIME MENU Function se

Chapter 1: System Components and Installation1-1) Environmental requirements for installation and safety This section describes the environmental requ

1-2) System ComponentsThe system consists of the following: • Check whether all the following devices and accessories are included with the main syste

English-141-3) CAMERA composition and installation method 1) Standard Camera composition (SOD14C) a. LensIt has a focal length of 3.8mm and makes it p

English-15e. SENSOR jackUsed to connect the sensor to the camera.f. SpeakerIt outputs the sound signal which was transfered from the monitor.• PIN con

English-163) PIR Camera composition① LensIt has a focal length of 3.8mm and makes it possible for you to observe a relatively widearea.➁ SpeakerIt out

English-17➃ 6-pin modular jackUsed to connect the camera to the monitor.⑤ 5-Pin Terminal BlockA terminal block for supplying backup power for the PIR

English-18(Sensor Detection Angle & Area)1) Vertical View Pattern2) Horizontal View Pattern

English-19➅ Function SwitchA function switch for the PIR sensor operation.⑦ PIR SensorA thermal heat sensor that detects infrared radiation projected

English-2IMPORTANT SAFETY INSTRUCTIONS1. Read these instructions.2. Keep these Instructions.3. Heed all warnings.4. Follow all instructions.5. Do not

English-20Camera installation Hints1. Do not install directly towards rising or setting sun. Can cause burn or damage to internal options.2. Do not

English-214) Installing the PIR Camera (SMM-PIRCAM)1. Choose an installation site that can sufficiently support 5 times the weight of the equipments

English-224. Connect the Camera connector(RJ-11) cable to the case-rear as well as the cable to be connected tothe terminal.5. Align the two holes of

English-236. Adjust the direction of the lens.1) Use the cross (+) screw driver to turn the screw (indicated by the arrow in the illustration)counte

English-244) Camera Mount Bracket(SBR-110) & Standard Camera(SOD14C) (1) OverviewCAMERA MOUNT BRACKET (SBR-110) is used to attach the camera to a

•Loosen the handle by turning it in a counter clockwise direction and then adjust the camera position . Tighten the handle, turning it clockwise, and

English-261-4) CAMERA Composition and Connecting Method toMONITORAfter positioning monitor and installing four cameras to a desired location, please c

English-271-5) External terminal connecting method for CAMERA and MONITOR 1) External terminal connecting method for CAMERA •An additional PIR sensor

English-28f) Connect the A/O (HOT) terminal on the rear panel to the Alarm IN terminal of the VCR.g) Connect the A/O (COLD) terminal on the rear panel

English-29Chapter 2: MONITOR FRONT PANEL KEYFunction and Using MethodFront Panel 2-1) TALK KEYTALK KEY allows users to transmit voice signal to intend

Graphic Symbol ExplanationThe lightning flash with arrowhead symbol, within anequilateral triangle, is intended to alert the user to thepresence of un

English-302-4) POWER SAVE- KEYAllows users to set POWER SAVE MODE of monitor. PICTURE screen is off when the POWER SAVE KEY is pressed, and the ON/OFF

English-312-8) PIP- KEYCan be used to see the main screen while Single screen is displayed. The main screen can be changedand transfered to another ch

2-13) ENTER- KEYAs a multi functional œœENTER√√ key, it allows users to 1. enter SET UP MENU movement andSETTING MODE and set data, and 2. display si

English-33Chapter 3: Setting each item function at SETUPMENUPressing the MENU BUTTON of the FRONT PANEL allows users to enter SETUP MENU and see thefo

3-2) DATE/TIME MENU Function setting •Function: Sets the display date format and current time.•Setting method :Move to #2. DATE/TIME MENU by using œ

English-353-4) DISPLAY MENU function setting •Function: Allows users to select the color and ON/OFF of borderline at QUAD DISPLAY.•Setting method: M

3-5) TITLE MENU Function setting •Function: Set the title of each camera at your discretion.•Setting method: Move to #5. TITLE MENU by using œœENTER

3-6) ALARM MENU Function setting •Function: Allows users to set the ALARM MODE for each camera.•Setting method: Move to #6. ALARM MENU by using œœE

English-3806/01/03 13:14:00NO CH MM/DD/YY HH:MM:SS EVT01 07 02/10/03 10:00:30 A02 01 02/11/03 11:22:00 L03 01 06/01/03 12:33:01 -04 02 06/01/03 13:0

English-39Chapter 4: DISPLAY MODE setting method4-1) SINGLE SCREEN DISPLAY Initial display mode of monitor is QUAD-A. In case users want to see the

IMPORTANT SAFEGUARDSCautionPower source is indicated on the rear of the set. It contains high-voltage parts. If you remove the cover, it may cause fir

English-404-2) QUAD MODE DISPLAY Users can switch SINGLE DISPLAY MODE and SEQUENTIAL DISPLAY MODE to QUADDISPLAY MODE, or QUAD-A (QUAD-B) to QUAD-B

English-414-3) AUTO SEQUENTIAL DISPLAY MODE Pressing on the SEQUENCE KEY on the front allows screen to automatically switch to SINGLEMODE full scre

English-424-4) PIP MODE DISPLAY Can be used to see PIP screen in Single screen mode.If you press the œœENTER√√ on PIP screen ,the main screen will

English-434-5) ZOOM MODE DISPLAY When users want to see zoomed image of a specific area of the display, press the ZOOM KEY in thefront to display z

English-44Chapter 5: Each product featureSOD14C : Standard CameraModel Name Broadcasting System Imaging Device Effective Pixels SSynchronization Resol

English-45Model Name Broadcasting System Imaging Device Effective PixelsSynchronization Resolution Signal Output S/N Ratio Minimum Scene Illumination

English-46Video InputVideo OutputVoice InputVoice OutputAlarm/Motion Features:Connected to AlarmBox/CameraSequenceEvent ListDisplay modeHorizontal Res

English-47Memo

Part No.: AA68-03537A-00Printed in KoreaIMPORTADO PORSAMSUNG ELECTRONICS MEXICO. S.A.DE C.V.Saturno No. 44, Col. Nueva Industrial VallejoGustavo A. Ma

8. Accessories : Do not place this monitor on an unstable cart, stand,tripod, bracket or table. The monitor may fall, causing serious injury to achild

13. Lightning : For added protection for this monitor during a lightningstorm, or when it is left unattended and unused for long periods of time,unplu

18. Replacement Parts : When replacement parts are required, be sure theservice technician has used replacement parts specified by Samsung orhave the

Information to userChanges or modifications not expressly approved by the party responsiblefor compliance could void the user's authority to oper

The party responsible for product compliance:SAMSUNG ELECTRONICS CO., LTD.America QA Lab of Samsung3351 Michelson Drive,Suite #290, Irvine, CA92612 US