Samsung SCU-VAC User Manual Page 40
- Page / 80
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
40_
setup
setup
CAMERA SETUP (SCU-9080/VAC)
Ú
This setup guide is intended for SCU-9080/VAC that may differ depending on the camera module.
Protocol Type (
SCU-VAC)
This enables you to specify the protocol type of
the camera module. Improper protocol settings
may result in an abnormal operation of the
product.
- SAMSUNG-T: SCB-3000/SHC-745
- SAMSUNG-E: SCB-4000
Lens Type (SCU-VAC)
FEEDBACK / NON F/B /SLA-12240 /
SLA-880:
Select a model if using a Samsung product
(SLA-12240/SLA-880); select a model that
supports feedback if using a third-party
product.
Reversed Zoom:
Depending on the wiring direction, Tele/Wide
can be controlled reversely. This is what you
can use to make the product work properly
without changing the wiring. (OFF: Disabled,
ON: Enabled)
Zoom Tele Pos.(Feedback/SLA-12240 Lens
Specifi cation):
If the feedback value from the motorized zoom
lens increases when you perform the zoom tele, you must set the value to Increase (Default)
so that the zoom factor will be displayed accordingly.
However, if an abnormal zoom factor is displayed, you must set the value to Decrease so that
the zoom factor will be displayed accordingly.
Reversed Focus :
Depending on the wiring direction, Far/Near can be controlled reversely. This is what you can
use to make the product work properly without changing the wiring.
Focus Near Pos.(Feedback/SLA-12240 Lens Specifi cation):
If the feedback value from the motorized zoom lens increases when you perform Focus Near,
you must set the value to Increase (Default) so that the Focus function works properly.
However, if the Focus function does not work properly, you must set it to Decrease so that it
works properly.
Display Zoom (Feedback/SLA-12240 Lens Specifi cation):
Select this if you want to display the value of the zooming position according to the feedback
from the motorized zoom lens. (However, the displayed value is a position value rather than
the zoom factor.)
z
-
z
-
-
-
-
-
-
Main Menu
► Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status
Camera Setting
#偓##Protocol Type# SAMSUNG-T
Lens Type SLA 880
Open Camera Menu
<SCU-VAC>
Camera Setting
► Open Camera Menu
<SCU-9080 >
- Positioning System 1
- ● SAFETY INFORMATION 3
- ● CONTENTS 7
- Features 8
- WHAT’S INCLUDED 9
- COMPONENT NAMES AND FUNCTIONS 10
- ● INTRODUCTION 11
- SCU-VAC WIRING DIAGRAM 12
- English - 13 13
- How to connect (SLA-880) 13
- How to connect (SLA-12240) 13
- Camera Wiring Interface Board 15
- Stand Alone DVR 16
- <Controller> 17
- Protocol Settings 18
- Communication Method Settings 19
- Termination Settings 19
- Initialize 19
- Baud Rate Settings 20
- CAMERA ID DIP SWITCH SETTINGS 21
- PREPARING ADAPTER AND CABLES 22
- PRODUCT CONFIGURATIONS 23
- CAMERA INSTALLATION 24
- INTERFACE SYMBOLS 26
- USING AND SETTING THE MENUS 27
- OSD Menu Chart 28
- CAMERA SETUP (SCU-2370) 29
- ###Focus Mode ONE SHOT 30
- 偓Zoom Tracking 30
- 偓Focus & Zoom 30
- 偓Mode AUTO 30
- 偓Camera Setting 30
- 偓White Balance ATW 31
- 偓Brightness 050 32
- 偓Exposure 32
- 偓Back Light OFF 33
- HLC Masking Area 34
- <HLC ON> 34
- <HLC OFF> 34
- W : INCREASE T : DECREASE 34
- 偓AGC MEDIUM 35
- 偓SSNR MEDIUM 36
- 偓Mode ON 37
- 偓Day & Night 38
- 偓Mode AUTO 38
- 偓Others 39
- 偓Sync INTERNAL 39
- CAMERA SETUP (SCU-9080/VAC) 40
- ● SETUP (SCU-VAC) 41
- RETURN 42
- MAIN MENU 43
- SYSTEM 43
- ► IMAGE 43
- ISOTHERM 44
- ► THRESHOLD 0 °C 44
- ● SETUP (SCU-9080) 45
- 偓Sequence Setting 46
- 偓PTZF Setting 46
- 偓Preset 46
- 偓Edit 001½ 47
- After Action OFF 48
- 偓Preset Name 49
- 偓OSD Setting 49
- 偓Status 50
- 偓Execute 50
- 偓Home Position 50
- 偓Pan Swing 51
- 偓Swing SEQ 51
- 偓Setting 52
- 偓Group 1 52
- 偓Group SEQ 52
- 偓PTZ Trace 53
- 偓Trace 1 53
- 偓Mode OFF 54
- 偓Auto Run 54
- P/T Setting 56
- 偓Area Name 57
- 偓P/T Setting 57
- 偓Area Setting 57
- 偓Area Masking 58
- 偓Position 58
- 偓Pump Enable OFF 59
- 偓Pump Enable ON 59
- 偓Prop. P/T 60
- 偓Image Hold 61
- OSD SETTING 62
- ALARM SETTING 63
- 偓Alarm Output 64
- 偓Alarm Setting 64
- 偓Aux Output 65
- INITIALIZE 66
- 偓Power On Reset 67
- TROUBLESHOOTING 68
- English - 69 69
- PRODUCT SPECIFICATIONS 71
- SCU-2370N SCU-2370P 72
- <SCU-2370> 72
- English - 73 73
- <SCU-VAC> 73
- <SCU-9080> 74
- SCU-9080 74
- English - 75 75
- English - 77 77
- Wall Mount 77
- Pedestal Mount 77
- DECLARATION OF CONFORMITY 78
Related products and manuals for Security access control systems Samsung SCU-VAC
(11 pages)
(11 pages)
(100 pages)
© 2020, manymanuals.com. All rights reserved. | 0.093 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals