Operation/ProgrammingP/No.:6806-0575-01A Before attempting to operate this product, please readthe instructions carefully.SAMSUNG TECHWIN CO., LTD.14
19SPEED DOME CAMERA18SPEED DOME CAMERAIt is necessary to connect the terminating resistance to the two units that are furthermost from the relevan
21SPEED DOME CAMERA20SPEED DOME CAMERACable PreparationFor SPD-2200 installation, the cables listed below have to be prepared. ●Power adapter cab
4) Wall Mounting (STB-270PW)Assembly used when an indoor and outdoor housing for a speed dome camera is to be mounted on a wall. 5) Ceiling Mounting
25SPEED DOME CAMERA24SPEED DOME CAMERAHow to Install the Camera (using the Embedded Housing)① Make a hole of 155mm in diameter in the ceiling to i
27SPEED DOME CAMERA26SPEED DOME CAMERAOSD Menu ConfigurationThis model enables dome camera setting, using the OSD (On Screen Display) menu display
29SPEED DOME CAMERA28SPEED DOME CAMERA●Dome Camera Users’Menu SettingsHow to Use the OSD MenuCheck whether the camera is set to manual mode and pr
31SPEED DOME CAMERA30SPEED DOME CAMERAExposureControls the camera exposure①AE Mode·Auto: Automatically adjusts the video signal brightness accordi
Note33SPEED DOME CAMERA32SPEED DOME CAMERA②D&N Mode (Day & Night Mode)Automatically detects the degree of darkness at night, or in poor li
35SPEED DOME CAMERA34SPEED DOME CAMERACamera settingOthers①SharpnessHighlights image contour by increasing the Aperture Gain of the camera. ②Mirro
37SPEED DOME CAMERA36SPEED DOME CAMERACamera setting③Tilt SwingActivates and sets Swing monitoring in the Tilt direction and deletes data ·Setting
Thank you for purchasing a SAMSUNG CCTV CAMERA.Before operating the camera, confirm the camera model and properinput power voltage. In order that you
39SPEED DOME CAMERA38SPEED DOME CAMERA⑥TourStarts and sets Group monitoring and deletes the data.•SettingSelects the procedure for the registered
41SPEED DOME CAMERA40SPEED DOME CAMERACamera settingPan LimitOn/OffPositionPress theEnter key3) P/T SettingP/T Setting MenuP/T SettingPan LimitT
43SPEED DOME CAMERA42SPEED DOME CAMERA④Area MaskingThe area to be excluded from the monitoring operation is displayed in white. Up to 8 areas can
45SPEED DOME CAMERA44SPEED DOME CAMERACamera setting4) OSD SettingOSD Setting MenuOSD SettingCamera ID ONCamera NamePreset Number ONPreset NameSeq
47SPEED DOME CAMERA46SPEED DOME CAMERACamera setting⑥Area NameSets the area names✽ With the area name off, the area can’t be displayed.⑤Sequence S
Alarm SettingAlarm Enable OFFAlarm InputAlarm OutMotion Detection49SPEED DOME CAMERA48SPEED DOME CAMERACamera setting③Alarm OutMatches each alarm
51SPEED DOME CAMERA50SPEED DOME CAMERACamera setting6) Initialize Setting①Power On Reset·Initialize a camera to the status prior to power supply②F
53SPEED DOME CAMERA52SPEED DOME CAMERA128mm207.5mm125.6mmAC 24VAC 24V●Dimension●Installation MethodCeiling attached Type Installation Installation
55SPEED DOME CAMERA54SPEED DOME CAMERASystem configurationSCC-3000Receiver1612364Power Supply161616M 1M 2M 3M 4SVR-1630SVR-1630SVR-1630SVR-1630101
56SPEED DOME CAMERA※ External Design and specification are subject to change without notice for improvement of product performance.Cautions●Samsung
Warning & Caution ... 6Main Features ...
7SPEED DOME CAMERA6SPEED DOME CAMERAWarning & CautionPlease read the instructions carefully for correct use of the product, and observe thesec
9SPEED DOME CAMERA8SPEED DOME CAMERANever expose the product to direct sunlight orharmful rays. Direct sunlight or harmful rays may cause fatal da
11SPEED DOME CAMERA10SPEED DOME CAMERARotary Switch 2 (SW2)Camera ID address settingswitch.Rotary Switch 1 (SW1)Camera ID address settingswitch.Co
13SPEED DOME CAMERA12SPEED DOME CAMERABracket Setup for Installation Initial Setting●Communication Protocol Setting (Installation Bracket)Select a
15SPEED DOME CAMERA14SPEED DOME CAMERA●Camera ID Switch SettingCamera ID SW2 SW1 RemarksID = 0 0 0 Not applicableID = 1 0 1ID = 2 0 2ID = 3
17SPEED DOME CAMERA16SPEED DOME CAMERACamera ID SW2 SW1 RemarksID = 192 C 0ID = 193 C 1ID = 194 C 2ID = 195 C 3ID = 196 C 4ID = 197
Comments to this Manuals