Samsung RF32FMQDBSR/AA Manual download pdf (Page 15)

setting up _15

01 SETTING UP

1. Connect the household water line to the

assembled compression ﬁtting.

- If you are using copper tubing, slip the

compression nut ( B ) (not supplied) and

ferrule (not supplied) on the copper tubing (not

supplied) as shown.

- If you are using plastic tubing ( B ), insert the

molded end (Bulb) of the plastic tubing ( B ) into

the compression ﬁtting.

• Do not use without the molded end (Bulb)

of the plastic tubing ( B ).

2. Tighten the compression nut ( B ) onto the

compression ﬁtting.

Do not over-tighten the compression nut ( B ) .

3. Turn water on and check for any leakage. If you

ﬁnd water drops or leakage in the connection

areas, turn off the main water supply. Check

the connections and, if necessary, tighten.

4. Flush 1 gallon of water through the ﬁlter before

drinking or using the water from the refrigerator.

(Flush approximately 6 minutes.) To ﬂush, press

a large glass or cup against the water dispenser

lever. Fill the glass, empty it into the kitchen sink

after it is ﬁlled, and then repeat.

5. After you turn on the refrigerator, let the ice

maker make ice for 1 to 2 days. Over that period

of time, throw out the ﬁrst 1 or 2 buckets of ice

the freezer makes to ensure all impurities have

been removed from the water line.

• Only connect the water line to a drinkable

water source.

If you have to repair or disassemble the water line,

CAUTION

cut off 1/4“ of the plastic tubing to make sure you

get a snug, leak-free connection.

• You can test the water line quickly using

a paper cup. Under normal conditions,

the water dispenser can ﬁll a 5.75 oz.

(170cc) cup in about 10 seconds.

COMPLETING THE SET UP

Now that you have your new refrigerator installed

in place, you are ready to set up and enjoy the

features and functions of the appliance.

By completing the following steps, your refrigerator

should be fully operational.

1. Make sure your refrigerator is in an appropriate

location with reasonable clearance between it

and the wall. Refer to installation instructions in

this manual.

2. Once the refrigerator is plugged in, make sure

the interior light comes on when you open the

doors.

3. Set the Temperature control to the coldest

temperature and wait for an hour. The freezer

will get slightly chilled and the motor will run

smoothly. Reset the refrigerator and freezer to

the temperatures you want.

4. After you plug the refrigerator in, it will take a

few hours to reach the appropriate temperature.

You can store food and drinks in the refrigerator

after the temperature is sufﬁciently cool.

If condensation or water drops appears

on both sides of fridge door’s central

part, turn the Energy Saver mode off after

removing the condensation.

(See the explanation on Energy Saver

button in the USING THE CONTROL

PANEL.)

Compression

Nut (1/4”)

(Assembled)

Ferrule

(Not supplied)

Plastic Tubing

(Assembled)

Compression

Fitting

(Assembled)

Molded

end(Bulb)

Compression

nut (B) (1/4”)

(Not supplied)

Copper tubing

(Not supplied)

Plastic tubing (B)

(Not supplied)

Household water supply line

Refrigerator

DA68-02918A-06.indb 15 15. 1. 7. �� 3:21

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 83 84

Comments to this Manuals

No comments

Samsung RF32FMQDBSR/AA Manual Page 15

Comments to this Manuals

Related products and manuals for Side-by-side fridge-freezers Samsung RF32FMQDBSR/AA