Samsung SCW-230E User Manual Page 3

  • Download
  • Add to my manuals
  • Print
  • Page
    / 5
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 2
System Requirements
Installing the CD-R/RW Drive
Installing the Device Driver
4 5
Before you install the CD-R/RW drive, we strongly recommend that you make certain
that your set-up meets the system requirements listed below.
Install the CD-R/RW drive in your computer horizontally, making sure that the Open/Close
button is on the right.
1
Turn OFF your computer. Remember to verify the
configuration jumper on the rear of the CD-R/RW drive.
To install the drive, proceed as follows.
2
Remove the cover of your PC(main unit of the computer).
3
Remove the blank cover panel of the 5.25 inch unit in
which the CD-R/RW drive is to be installed.
4
Connect the CD-R/RW drive to the IDE interface and
power cables located inside your computer.
Connectors are keyed so it is impossible to put them in
an incorrect position. Do not force the connectors, if they
do not seem to fit.
5
Install the CD-R/RW drive into the unit and secure it with
mounting screws (recommended standard M3x6).
☛ ◆ Depending on your PC model, you may need to attach
☛ ◆ guide rails to the drive, so that the drive is held firmly in place.
☛ ◆ On the ground that the guide rails are parts of the computer,
☛ ◆ if you don’t have these, please purchase separately.
If you use screws that are longer than the recommended
☛ ◆ standard, you may damage the drive.
6
Put the cover back on your PC.
Item Description
Type of computer
Pentium 75MHz(or higher) with an IDE interface
16MB RAM(or higher)
528MB higher(Transfer Rate 800KB/sec higher Access,
Time 20m/sec Lower)
5.0(or higher)
TIP:For MS-DOS, The CD-R/RW drive can only Read a
disc without Premaster Software
RAM
Hard drive
MS-DOS
Microsoft
®
Windows 95
®
or Windows NT 4.0
®
TIP:For Windows NT
®
, we recommend Service Pack2,
Version 4.00.1381.
Windows
You can install the device driver for DOS or for Windows.
TIP : You can use the CD-R/RW drive to only read a disc in DOS/Windows 3.1.
1
Turn on your computer and wait for it to boot.
7
Reboot your system.
Result:
The computer restarts
Both the device driver and MSCDEX are loaded.
6
When the Setup Completed screen is displayed, remove the installation
floppy disk from the drive.
2
Insert the driver disk into a floppy disk drive (usually the A drive).
4
Run the CDSETUP program:
5
To... Then enter...
Confirm the installation Y
Exit without installing N
Result
:
If you answer Y(Yes), the installation program automatically
Creates a SAMSUNG directory on your hard disk
Copies the required softwares (mscdex.exe and sscdrom.sys)
Modifies the CONFIG.SYS and AUTOEXEC.BAT files
3
If you are a... Then...
DOS user
Windows user
3.1
Windows 95 user
/NT 4.0
Type a: at the DOS prompt.
Press the RETURN key.
Access the File Manager.
Click on the A icon.
When you are in Windows 95, it is not
necessary to install Device Driver.
Whereas, when you are in Dos Mode of
Windows 95, then install as follows.
Click on MY COMPUTER icon.
Click on the A icon.
If you are a... Then...
DOS user
Windows user
3.1
Type CDSETUP after the a: prompt.
Press RETURN.
Double-click CDSETUP.EXE from the
Windows File Manager.
English
SCW-230(E/G/F/S) 3/31/00 2:35 PM Page 3
Page view 2
1 2 3 4 5

Comments to this Manuals

No comments