Samsung UN55C6500VFXZA User Manual download pdf

Step 4: Connect External Devices

Connecting an AV device (DVD/Blu-ray player, cable/satellite box, etc.)

Step 1: Install the Stand

Follow the steps below to connect the TV to the stand.

✎

NOTE

Make sure to distinguish between the front and back of the Stand and

Guide Stand when assembling them.

Make sure that at least two persons lift and move the LED TV.

Stand the product up and fasten the screws. If you fasten the screws with

the LED TV placed down, it may lean to one side.

1 Connect the Guide Stand to the

Stand using four screws (M4 X L8)

as shown.

2 With your TV upright, connect the

TV to the Stand as shown.

3 Fasten two screws (M4 X L8) at

position 1, and then fasten three

screws (M4 X L8) at position 2.

Rear

Screws (M4 X L8)

Step 2: Install the Batteries into the Remote

To install batteries into your remote control,

follow these steps:

1. Lift the cover on the back of the remote

upward as shown in the ﬁgure to the

right.

2. Install two AAA batteries.

✎

Make sure to match the + and - ends of the batteries to the diagram in

the battery compartment.

3. Replace the cover.

Step 3: Connect Power and Antenna or Cable

Quick Setup Guide

Congratulations on the purchase of your new Samsung TV.

Read this setup guide to get your TV up and running quickly.

1-800-SAMSUNG (1-800-726-7864)

Samsung Electronics America, Inc.

85 Challenger Road Ridgeﬁeld Park, NJ 07660-2112

Samsung Electronics Canada Inc.

55 Standish Court Mississauga, Ontario L5R 4B2

Call Center hours of operation: Mon-Sun, 9:00 AM -12

AM EST.

To register this product, visit: www.samsung.com/

STOP

Please do not return this unit.

If you have problems operating your

TV, call:

1-800-SAMSUNG (1-800-726-7864)

For web support please visit:

www.samsung.com/support

Step 5: Run Plug & Play

When you turn on your TV for the ﬁrst time, it automatically launches the Plug &

Play function. With Plug & Play, you can select the On Screen Display language, set

the clock mode, and launch the TV’s channel memorizing process.

It also displays connection instructions similar to those in this guide.

To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow

buttons on your remote. To make a selection, press the ENTER

button.

To skip a screen, press the MENU button. To turn on your TV, press the POWER

button on the remote or on the TV. To run Plug & Play, follow these steps:

1 Using your remote control, select

the language for the On Screen

Display (OSD), and then press the

ENTER

button.

2 Select Home Use, and then

press the ENTER

button.

If you select Store Demo, the TV will reset your picture and audio settings

every 30 minutes.

3 Select Antenna Source. If Antenna Source is Air, Cable or Auto, you must

select your cable system type. After selecting source, select Search; then

press the ENTER

button on your remote.

✎

Most cable systems are Standard(STD) systems, If you are not sure about

what kind of cable system you have, contact your cable company.

✎

If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After

Plug & Play is complete, set your TV to Channel 3 or 4, according to the

directions for your cable or satellite box.

4 The TV memorizes the available channels. This process can take up to 45

minutes.

5 After the TV has memorized the channels, choose the Clock Mode. Select

Auto if you have a digital channel in your area. Select Manual if you don’t, or

if you have a cable or satellite box. When done, press the ENTER

button.

✎

If you select Manual, the clock setting screen appears.

6 Select the daylight savings time setting: Off or On, and then press the

ENTER

button.

✎

This function is only available when the Clock Mode is set to Auto.

7 Select the time zone in which you live, and then press the ENTER

button.

8 After the time zone screen, The connection method for best HD screen

quality is displayed. Press Right arrow button on your remote to view each

screen in succession. Press the Blue button to skip this section.

9 The Enjoy your TV. screen appears. Then press the ENTER

button.

Changing the Screen Size

Your TV has several screen size options, each designed to work best with speciﬁc

types of video input. If you have a cable box or satellite receiver, it may have its own

set of screen sizes as well.

To change the screen size, press the P.SIZE button on your remote. The ﬁrst time

you press it, your TV displays the current setting. Thereafter, each time you press

the P.SIZE button, you change the size of the picture on the screen.

The following sizes are available:

16:9 Wide screen 4:3 Standard screen Wide Fit

Zoom 1 Zoom 2 Screen Fit

✎

Screen Fit: Displays the full image without any cut-off when HDMI (720p /

1080i / 1080p) or Component (1080i / 1080p) signals are inputted.

Changing the Picture Mode

Your TV has four preset Picture Modes with factory adjusted settings, each

designed to give you an excellent picture under speciﬁc conditions.

The Picture Modes are listed and described in the table below:

Mode

Description

Dynamic

Brightens picture. For a vibrant, enhanced image in brightly lit or

sunny room.

Standard

For a bright, detailed picture in a normally lit room.

Natural

For a comfortable, easy-on-the-eyes picture in a normally lit room.

Movie

For a studio quality cinema picture in a dimly lit or dark room.

To change the Picture Mode, follow these steps:

1. Turn on your TV, press the TOOLS button on your remote. The Tools menu

appears.

2. Using the ▲ or ▼ on your remote, select Picture Mode.

3. On the Picture Mode menu, use the ◄ or ► on your remote to select the

Picture Mode you want.

4. Press the EXIT button to exit the menu.

Setting the Clock

Before you can use your TV’s On/Off Timer, you must set the clock. To set the

clock, follow these steps:

1. Turn on your TV, press the MENU button on your remote, then select Setup →

Time.

2. Select Clock Mode, and then press the ENTER

button.

3. Choose Auto or Manual.

If you select Auto, the current time will be set automatically using the time

from a digital channel.

If you select Manual, you can set the Month, Day, Year, Hour, Minute

and am/pm directly by pressing up, down, left and right arrow button on

your remote.

4. Press the RETURN button on your remote when done.

Connecting an audio device (Home Theater, etc.)

Connecting a PC

HDMI OUT

AUDIO OUT

COMPONENT OUT

AUDIO OUT

DVI OUT

AUDIO OUT

VIDEO OUT

AUDIO IN

OPTICAL

Analog Audio connection

Ampliﬁer / DVD home theater

Using an Audio Cable

Move

Enter

Select Language of the OSD.

Menu Language :

Plug & Play

English

Español

Français

DVI OUT

AUDIO OUT

PC OUT

HD connection

Using an HDMI to DVI Cable

Using a D-Sub Cable

Digital Audio connection

Using an Optical Cable

Digital Audio System

Best Connection

HD connection (up to 1080p)

Using an HDMI Cable

DVD, Blu-ray player, HD cable box,

HD STB (Set-Top-Box) satellite

receiver

Device

HD connection (up to 1080p)

Very Good Connection

Using an HDMI to DVI Cable

Device

Using a Component Cable

Good Connection

Component connection (up to 1080p)

DVD, Blu-ray player, cable box,

STB satellite receiver, VCR

Device

Lowest Quality Connection

Audio/Video connection (480i only)

Using an Audio/Video Cable

DVD, Blu-ray player, cable box,

STB satellite receiver, VCR

Device

Top view

Rear

Guide Stand

Screws (M4 X L8)

Stand

Use one of the connections below to connect your

TV to an external A/V device.

We recommend using HDMI for the highest picture

quality.

✎

When connecting to AV IN 1 on the back of

your TV, attach the video cable (yellow) to the

green jack next to the AV IN 1 label. The jack

will not match the color of the video cable

(yellow).

Connect your TV to your Home Theater or other

audio device to enjoy enhanced Sound quality.

Connect your TV to a PC to use it as a Monitor.

VHF/UHF Antenna

Connect Ant In to

• Wall cable jack

• VHF/UHF Antenna

• Cable or Satellite box

Ant or Cable Out

Use a 75 ohm (round) cable.

Antenna Cable

(Not Supplied)

Audio Cable (Not Supplied)

HDMI to DVI Cable (Not Supplied)

Audio Cable (Not Supplied)

Component Cable (Not Supplied)

HDMI Cable (Not Supplied)

Video Cable (Not Supplied)

Optical Cable (Not Supplied)

Audio Cable (Not Supplied)

HDMI to DVI Cable

(Not Supplied)

D-Sub Cable (Not Supplied)

Audio Cable (Not Supplied)

[QSG-6500]BN68-02714C-02Eng.indd 1 2010-09-03 오후 5:27:50

1 2

Summary of Contents

Page 1 - Quick Setup Guide

Step 4: Connect External DevicesConnecting an AV device (DVD/Blu-ray player, cable/satellite box, etc.)Step 1: Install the StandFollow the steps below

Page 2 - Step 6: Remote Control

Step 6: Remote ControlRemote Control Buttons and Functions ✎This is a special remote control for the visually impaired persons and has Braille points

Samsung UN55C6500VFXZA User Manual

Browse online or download User Manual for Televisions Samsung UN55C6500VFXZA. Samsung UN55C6500VFXZA User Manual [en] [de]

Summary of Contents

More documents for Televisions Samsung UN55C6500VFXZA

Comments to this Manuals

Samsung UN55C6500VFXZA User Manual

Browse online or download User Manual for Televisions Samsung UN55C6500VFXZA. Samsung UN55C6500VFXZA User Manual [en] [de]

Summary of Contents

More documents for Televisions Samsung UN55C6500VFXZA

Comments to this Manuals

Related products and manuals for Televisions Samsung UN55C6500VFXZA