Samsung SC-152A User Manual download pdf

Front View of the CD-ROM Drive

System Requirements

Rear View of the CD-ROM Drive

4 5

6 7

Headphone Connector

The sound output terminal enables you to plug stereo headphones into the drive.

It requires a 3.6 mm stereo mini-jack.

23 4 5

Digital output terminal

You can connect a sound card or MPEG card which support Digital output

terminal to your drive using this two-pin terminal.

Turn OFF your computer. Remember to verify the

configuration jumper on the rear of the CD-ROM drive.

Remove the cover of your PC(main unit of the computer)

Remove the blank cover panel of the 5.25 inch unit in

which the CD-ROM drive is to be installed.

Put the cover back on your PC.

Install the CD-ROM drive into the unit and secure it with

mounting screws (recommended standard M3x6x4)

☛

◆

Depending on your PC model, you may need to

attach guide rails to the drive, so that the drive is

held firmly in place.

☛

◆

If you use screws that are longer than the

recommended standard, you may damage the

drive.

Before you install the CD-ROM drive, we strongly recommend that you make certain

that your set-up meets the system requirements listed below.

Installing the CD-ROM Drive

Install the CD-ROM drive in your computer horizontally, making sure that the Open/Close

button is on the right.

To install the drive, proceed as follows.

Sound output terminal

You can connect a sound card to your drive using this four-pin terminal.

☛ This function is not covered in detail in this guide. Refer to the documentation

supplied with your sound card.

Master/slave select terminal

Usually, this is a pre-set configuration as illustrated below.

☛ Verify that the setting is as illustrated. If it is not, simply remove the jumper

and place it in the correct position.

Interface terminal

This input/output interface terminal is used to connect the 40-pin flat cable from

the IDE interface to the CD-ROM drive.

Power terminal

The power terminal is a four-conductor male plug.

Eject Button

Disc compartment

The compartment opens and closes automatically when you press

the Eject button.

Eject Button

Emergency eject hole

If the compartment does not open when you press the Eject button, power off

the computer, insert a pin or unfolded paper clip in the hole and push firmlhy)

Headphone volume control

This headphone volume control adjusts the volume for your headphones. You can only

use the headphone jack and volume control when you have installed the required

software utilities. For example, the Microsoft Windows Media player can be used.

LED

Connect the CD-ROM drive to the IDE interface and power

cables Iocated inside your computer.

☛ Connectors are keyed so it is impossible to put them in

an incorrect position. Do not force the connectors, if they

do not seem to fit.

Item

Windows version

MS-DOS version

Disk space

Free expansion unit

Type of computer

Description

Windows 95 OSR2 / 98 / 2000 / ME / XP

Windows NT 4.0 (or higher)

5.0(or higher)

100KB minimum

5.25 inch

IBM 486SX 20MHz (or higher) with an IDE interface

(or a 100% IBM-compatible computer)

CD-ROM DRIVE

SC-152

User's Guide - ENGLISH

Technical Specifications

Max. 7800KB/s

SC-152

SECTIONS

DISC

DRIVE PER -

FORMANCE

FRONT PANEL

REAR PANEL

OPERATING

ENVIRONMENT

GENERAL

RELIABILITY

ERROR RATE

Disc types supported

Disc diameter

Data transfer rate

Access time (

typical

)

Data buffer capacity

Laser

Slide mechanism

Spindle motor

Load mechanism

Button

Indicator(LED)

Headphone output

Volume control

Required power

Interface connector

Audio output

Jumper block

Work area

Storage area

Dimensions

SC-152L

SC-152A

Net weight

MTBF

CD-DA, CD-ROM Mode-1, CD-ROM XA Mode-2 Form-1,

Form-2, CD-Plus, CD-Extra, Photo-CD(Single, Multi-session),

Video CD ready, Enhanced CD, CD-I/FMV, CD-R/RW

120mm or 80mm

PIO Mode - 4. DMA MW2, Ultra DMA(option)

75ms(typical)

128KB

Semiconductor Laser

Gear motor

Brushless motor

Tray, DC motor(Soft Eject)

Mode-1 : 1block / 10 bits, Mode-2 : 1 block/10 bits

Eject(Open/Close)

Busy

Stereo Mini - jack (Ø 3,6 mm) 0.60 ± 20% (Vrms) 33Ω

Dial type

+5V DC 1.3A, +12V DC 1.5A

ATAPI

Line out 0.70 ± 20%(Vrms), 47kΩ

Device configuration jumper

Temperature : 5~45 °C, Humidity : 8~80%

Temperature : -40~60 °C, Humidity : 5~90%

850g (set only)

125,000 POH(Duty 20%)

148.2 (W) x 42(H) x 202(D)mm

SAMSUNG continually strives to improve its products. Both the design

specifications and these user instructions are thus subject to change without

notice.

Dimensions

Net weight

740g (set only)

148.2 (W) x 42(H) x 184(D)mm

12 9

Safety Precautions

The following diagrams illustrate the precautions to be taken when using

your CD-ROM drive.

Setting Up the Device Driver

It is not necessary to set up additional device driver for Window

95/98/2000/ME/XP/NT because it uses the device driver provided by the

Window.

Solving Technical Problems

☛ Frictional sound detected during the operation of Spin-Up and Stop is made ABS

(Auto Balance System), not by malfunction.

◆

Automatic Setup

◆

Manual Setup

LAST DRIVE = Z

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

DEVICE = C :\SAMSUNG\SSCDROM.SYS /D : SSCD000 /V

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

C :\SAMSUNG\MSCDEX /D:SSCD000

1Insert the setup diskette in the diskette drive and change the directory to A:,

where A: is the diskette drive.

To do so, type A: after the C:\ prompt and press [Enter].

2Type CDSETUP and press [Enter].

3Reboot the computer.

1Make the C:\SAMSUNG directory.

2Copy the files from the diskette to the C:\SAMSUNG directory.

To do so, type COPY A:

C:\SAMSUNG after the C:\ prompt and press

[Enter].

3Edit the CONFIG.SYS file.

Add the DEVICE=C:\SAMSUNG\SSCDROM.SYS \D:SSCD000 /V entry.

4Edit the AUTOEXEC.BAT file.

Add the C:\SAMSUNG\MSCDEX /D:SSCD000 entry.

5Reboot the computer.

You must not use the drive in any manner other than that specified in this guide.

Avoid exposing your eyes or skin to direct or scattered radiation.

CAUTION

Do not attempt to repair the CD-ROM drive yourself. Contact

your dealer or local SAMSUNG representative for all repairs.

If you make any adjustments or perform any operations other

than those specified in this guide, you run the risk of exposure to

hazardous radiation.

WARRANTY

Please refer to the Samsung limited warranty statements.

Precautions

1.To reduce the risk of fire or electric shock, do not expose

this appliance to rain or moisture.

2.Always check each disc for cracks before using it. If there are

cracks on the surfaces, especially around the border of the

center hole, we recommend that you make a copy of the disc

immediately and then stop using it. If you continue using the

disc, it will probably develop more cracks and eventually cause

irreparable damage.

3.Do not use poor quality discs:

● From unknown sources

● Without any copyright

● Scratched or damaged in any way

Problem

Meaning / Solution

The CD-ROM drive is not

detected by the computer.

◆ Check that the power, audio and IDE cables are

correctly connected to the computer.

◆ Change the IDE cable and reconnect it to the computer.

Preferably, connect a second IDE cable to the CD-ROM

drive in master mode.

◆ Check the position of the jumper in the master/slave

select terminal.

◆ Reinstall the device driver or update it with the latest

version by downloading it from the Samsung Web site.

- www.samsungodd.com

www.samsungelectronics.com

◆ This case may occur when there is a Windows

installation problem; reinstall Windows.

◆ Check whether the audio cable is correctly connected

to the sound output terminal on the CD-ROM drive and

the sound card CD-IN terminal.

◆ Check that the sound card is operational.

◆ Adjust the volume control.

◆ Install the latest version of the device driver.

◆ Check whether the CD is of good quality and clean it,

if necessary.

◆ Check that the power cable is correctly connected.

◆ Power off and disconnect the PC. Insert a pin or

unfolded paper clip in the emergency hole and push

firmly until the disc compartment opens.

◆ Adjust the size of the replay screen.

◆ After checking the display resolution, adjust it, if

necessary.

◆ The computer may not recognize the disc if you start

playback too quickly after inserting the disc.

Open and close the disc compartment and try again.

◆ Clean the disc and try again.

◆ The interface mode of the sound card is AT-BUS.

You must therefore connect the CD-ROM drive to the

IDE port on the PC mother board, rather than to the

sound card, or install an IDE-compatible sound card.

After installing the CD-ROM

drive, the PC gets slower.

The CD-ROM drive is not

recognized by MS-DOS.

The CD-ROM drive is not

detected by Windows.

No sound is heard from an

audio CD.

A CD is not read or is read too

slowly.

The disc compartment will not

open.

When the MPEG software plays a

Video CD, the pictures are not regular

and the running speed is too slow.

The Disc is not in message is

displayed even though a disc

has been inserted.

The CD-ROM drive is not

detected after it is connected

to a sound card.

* The design of this product can be more or less changed according to its

characteristics.

FCC Compliance

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be

deter-mined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

• Re-orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

✱ Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment

BG68-00326C Rev.00

http://www.samsungodd.com

www.samsungelectronics.com

1 2

Summary of Contents

Page 1 - User's Guide - ENGLISH

1Front View of the CD-ROM Drive2System RequirementsRear View of the CD-ROM Drive34 56 71123456Headphone ConnectorThe sound output terminal enables you

Page 2 - Bedienungsanleitung

1Vorderseite des CD-ROM-Laufwerks2System AnforderungenRückseite des CD-ROM-Laufwerks34 5 6 71KopfhöreranschlußAn diese Buchse können Sie einen Stereo-