Samsung Series r5+ 550 Installation Guide Page 415
- Page / 430
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Hardware Installation Guide
revision 88 — 415
78. Cypress Timer (BAS-CCK-1201-M)
The Cypress Timer is ideal for Time and Attendance applications where the Access Control System’s time
must be displayed. Up to 32 clocks can be driven from one time source over a single twisted pair network.
The enclosure is weather resistant making it ideal for exterior installation.
• Adds time of day displays to Access Control and Time & Attendance Systems.
• Low profile facilities mounting at reader location.
• Can be used indoor or outdoor.
• Standard or Military Time Formats.
78.1. BAS-CCK-1201-M Time Displays: Functional Description
The clocks are used to display the time from the ISC. When the ISC sends a time stamp to the clock, the
clock's internal time base is updated; however, the clock's time stamp is not used. The time stamp that comes
directly from the ISC is still used. In other words, the clock's internal time base is updated but is not used
unless nothing is received from the ISC or there is a loss of clock information. In order to use DST (Daylight
Savings Time), this option must be turned on in the software application for that panel.
CYPRESS
Computer Systems, Inc.
RS-485
ISC
- Table of Contents 10
- GUIDELINES 13
- HARDWARE 13
- INSTALLATION 13
- 1.1. Power Inputs 15
- 1.1.1 AC Power 15
- 1.1.2 DC Power 15
- Belden Wire Specifications 17
- 1.5.2 RS-485 Cable 18
- 1.5.5 Cable Termination 18
- 1.6. RS-232 Interfaces 19
- 2.1.1 Device Placement 20
- 2.1.2 Power Requirements 20
- 2.1.3 Current Overload 20
- 2.2. Mounting 22
- DO NOT DISPOSE 23
- Knockout diagram 24
- 2.3. Ground Wiring 25
- 2.3.1 DC Negative 25
- 2.3.3 Grounding System 25
- 2.3.4 Safety Ground 26
- 2.4. Alarm Input Wiring 26
- PVC Cover Wire 28
- PVC Cover Wire/or Drain 28
- 2.7. Weather Proofing 30
- 3. Relay Contact Protection 32
- 5. Troubleshooting 35
- BAS-500 37
- INTELLIGENT 37
- CONTROLLER 37
- 6. Overview of the BAS-500 39
- BAS-500 Board 40
- 7. Installation 41
- RS-232 Communications 42
- RS-485 Line Termination 42
- 7.1.3 Power 44
- 7.1.5 Other 46
- ON ON ON 47
- 8.1.3 Communication Baud Rate 48
- 8.2. Installing Jumpers 49
- 9. Maintenance 50
- 10. Specifications 52
- BAS-1000 53
- 11. Overview of the BAS-1000 55
- The ISC Board 56
- (Maximum of 8 control panels) 60
- Ports 2 - 5 62
- 14. Maintenance 70
- 15. Specifications 72
- BAS-2000 73
- 16.2. The BAS-2000 Board 76
- RS-485 Communication Wiring 82
- 38400 bps 86
- PASSWORD STATUS DIP SWITCH 8: 86
- Not required (default) off 86
- Required ON 86
- 18.2.1 RAM Chip Size 88
- 3.00 (76.20) 88
- 4.00 (101.60) 88
- Input/Output 90
- Control Module(s) 90
- SETTING UP ISC 95
- COMMUNICATIONS 95
- Setting Up ISC Communications 100
- Hardware Installation Guide 101
- Network Requirements: 103
- Machine Requirements: 103
- Jumpers 119
- Switches 119
- ISC Settings 135
- Configure the RocketPort 136
- Configure the IP Address 137
- Configure Ports 137
- BAS-1100 INPUT 139
- CONTROL 139
- BAS-1100 Input Control Module 142
- 12345678 149
- BAS-1200 OUTPUT 155
- The Output Control Module 158
- 27. Installation 160
- ... OR 162
- Intelligent System Controller 164
- Elevator Control Room 164
- Maximum: 164
- 4000 feet 164
- 5 conductors 164
- 32 Downstream 168
- BAS-1300 SINGLE 171
- INTERFACE 171
- 30.2.1 Status LEDs 174
- 31.1.2 Upstream Communication 176
- Relay Contact (DC Strike) 178
- Relay Contact (AC Strike) 178
- 32. Configuration 181
- 32.1.1 Device Address 182
- 32.1.3 Cabinet Tamper 183
- 32.1.4 EOL Termination 183
- 33. Specifications 185
- BAS-1320 DUAL 187
- The DRI includes eight (8) 189
- Dual Reader Interface Module 190
- 34.2.1 Status LEDs 191
- 35. Installation 192
- 35.1.2 Upstream Communication 194
- Monitors 195
- 35.1.5 Relay Outputs 197
- Relay Outputs 198
- Typical Reader Wiring 198
- 35.2. Elevator Control 199
- 36.2. Installing Jumpers 204
- 37. Specifications 205
- BAS-4000 207
- MULTIPLEXER 207
- 38. Overview 209
- 38.2. The Multiplexer Board 210
- 39. Installation 211
- RS-485 4-WIRE COMMUNICATIONS 212
- 39.1.2 Power 213
- RS-232 (PORTS 2-5) 214
- 40. Configuration 215
- 41. Specifications 216
- BAS-8000 STAR 217
- 42. Overview 219
- 42.2.1 Status LEDs 220
- 43. Installation 221
- FiberOption Converter 222
- 43.1.3 Power 224
- 43.2. Wiring and Termination 225
- 5 4 3 2 226
- 44. Configuration 227
- 44.2. Installing Jumpers 228
- 45. Specifications 229
- BAS-8000 Star Multiplexer 230
- BAS-2005W 231
- MAGNETIC CARD 231
- ACCESS READER 231
- 46. Overview 233
- 47. Installation 234
- 48. Configuration 236
- 48.2. TTL Interface 237
- 48.3. Grounding the Reader 237
- 48.4. Reader Verification 237
- 48.5. Status LEDs 237
- 48.6. Maintenance 238
- 48.7. Product Identification 238
- 49. Specifications 239
- Optional Wall Plate, WP-10 240
- 49.2. Reader Weather Shield 241
- BAS-2010W/2020W 243
- 50. Overview 245
- 51. Installation 246
- 52. Configuration 249
- Switch/Jumper Position 250
- 52.4. TTL Interface 251
- 52.5. Grounding the Reader 252
- 52.6. Reader Verification 252
- 52.7. Status Indicators 252
- 52.8. Maintenance 253
- 52.9. Product Identification 253
- 53. Specifications 254
- 53.2. Reader Weather Shield 256
- LENELPROX 259
- 54. LenelProx Readers 261
- 54.2.2 Power 262
- 54.2.3 Grounding 262
- 54.2.4 Wiring 263
- 54.3. LenelProx LPMM-6800 263
- 54.3.1 Installation 263
- LenelProx Readers 264
- 54.3.2 Specifications 265
- 54.4. LenelProx LPSP-6820 266
- 54.4.1 Installation 266
- LenelProx LPSP-6820 267
- 54.4.2 Specifications 268
- 54.5. LenelProx LPKP-6840 269
- 54.5.1 Installation 269
- Reader 1 271
- 54.5.2 Operating Modes 272
- 54.5.3 Specifications 272
- 54.6. LenelProx LPSR-2400 273
- 54.6.1 Installation 273
- 54.6.2 Specifications 275
- 54.7.1 Installation 275
- Power Supply - Voltage 278
- Power Supply - Current 278
- Distance from Metal 278
- Metal Compensation 278
- Distance between Readers 279
- Credentials 279
- Environment 279
- Field Test 279
- Site Test 279
- 54.8. LenelProx LPLR-911 280
- Wiring Requirements 281
- Power Supply 281
- Grounding 282
- Measuring Reader Distance 282
- 54.8.4 Specifications 287
- LENEL KEYPADS 289
- 55. Lenel Keypads 291
- 55.1.1 Wiring the BAS-1300 292
- 55.1.2 Wiring the BAS-1320 293
- 55.2. Reader Specifications 293
- Lenel Keypads 294
- BAS-500B 295
- BIOMETRIC 295
- 56. Overview of the BAS-500B 297
- The BAS-500B Board 298
- 57. Installation 299
- RS-485 Communications 300
- Termination 301
- Ports 2 - 3 302
- 58. Configuration 303
- 58.1.3 Downstream Baud Rate 305
- 58.2. Installing Jumpers 305
- 59. Maintenance 306
- 60. Firmware 307
- 61.1. RSI Biometric Readers 308
- 61.1.1 RSI Enrollment 309
- RSI Handkey ID3D-R 312
- Access Control Server / 314
- Enrollment 314
- Back of RSI Handkey unit 315
- Handkey version F3 316
- Resetting the Handkey Reader 319
- Reader Addressing 326
- Additional Notes 327
- Enabling the Keypad 328
- 62. Specifications 330
- BIOCENTRIC 331
- SOLUTIONS 331
- 63. Overview 333
- • Cryptoflex for Windows 2000 334
- Reflex USB Interface Reader 335
- Philips Electronics Standard 336
- HID Corp 336
- 65. Verification Readers 338
- Configuration tab 339
- Power Up Sequence 340
- Standard Operation 340
- Button Operation 341
- Normal Error Conditions 341
- Abnormal Error Conditions 342
- Biocentric Solutions 344
- Common Problems and Solutions 345
- 66.1.3 Fingerprint Pressure 347
- 66.1.4 Trade-offs 348
- 66.1.5 Specifications 348
- 66.1.6 CombiSmart 348
- 66.1.7 GuardDog 349
- BIOSCRYPT 351
- 67. Overview 353
- Bioscrypt Readers 354
- 68. Installation 356
- 68.4. Reader Configuration 359
- 68.4.2 Firmware 360
- 68.4.3 LED Settings 360
- 68.4.4 Smart Card Settings 362
- Indicator Light 368
- 00010203 370
- 04050607 370
- 68.7.1 Termination 371
- 68.8. V-StationA Readers 371
- Back of V-Station Unit 376
- Dual Reader 376
- Interface Module 376
- LNL-BIO007 381
- BIOGUARD 381
- 69. Overview 383
- 70. Installation 384
- LNL-BIO007 BioGuard Reader 386
- 71. Specifications 388
- BAS-500W 389
- WIRELESS 389
- 72. Overview of the BAS-500W 391
- (battery not used) 392
- 73. Installation 393
- 73.1.3 Power 395
- 74. Configuration 397
- 74.1.3 Downstream Baud Rate 399
- 74.2. Installing Jumpers 399
- 74.3. Firmware 399
- 75. Wyreless Readers 402
- 76. Specifications 403
- COMMAND 405
- 77. Command Keypad Overview 407
- Command Keypad 408
- 77.1.3 DIP Switches 409
- 77.1.4 Jumpers 409
- 77.1.5 LNL-CK Configuration 409
- 77.1.6 Command Programming 410
- CYPRESS TIMER 413
- Computer Systems, Inc 415
- Cypress Timer 416
- Multi-Drop 417
- Central Power 417
- Multi-Drop, Local Power 417
- 78.2. Wall Mounting 421
- B.A.S.I.S 430
Related products and manuals for Security door controllers Samsung Series r5+ 550
(632 pages)© 2020, manymanuals.com. All rights reserved. | 0.380 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals