Samsung Series r5+ 590 Installation Guide Page 326
- Page / 632
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
LNL-1300-U Single Door Controller Module
326 —
revision 1
Power source wiring
Notes: Be sure to observe polarity.
Do not use an AC transformer to directly power the Single Reader SDC Interface Module.
62.9 UL Listed Installations
For UL Installations, the following must be observed:
• All field wiring terminals are suitable for single wire only.
• Use 22 AWG minimum for wiring of RS-485, Input I1, and reader data.
• Input I2 “Do not supervise for UL” and therefore cannot be used for UL installations.
• RS-485, clock & data reader communications “Not Evaluated by UL” and therefore cannot be used in
UL installations.
• RS-485 4-wire is “Not Evaluated by UL” and therefore cannot be used in UL installations.
• The use of AC Strikes is “Not Evaluated by UL” and therefore cannot be used in UL installations.
• Reader power for UL installations: 300 mA maximum for an operating temperature range of -10 to
+49°C (14 to 120°F).
• Environmental for UL installations:
- Temperature: -10 to +49°C (14 to 120°F) operating
- Humidity: 85+/-5% at 30+/-2°C (86°F)
- Hardware Installation Guide 1
- Table of Contents 10
- HARDWARE 17
- INSTALLATION 17
- GUIDELINES 17
- 1.1 Power Inputs 19
- 1.1.1 AC Power 19
- 1.1.2 DC Power 19
- Belden Wire Specifications 21
- 1.5.1 RS-485 Cable 22
- Cable Cross Reference Table 22
- 1.5.4 Cable Termination 23
- 1.6 RS-232 Interfaces 23
- 2.1.1 Device Placement 24
- 2.1.2 Power Requirements 24
- 2.1.3 Current Overload 24
- 2.2 Mounting 29
- STANDOFFS 30
- LNL-CTX knockout diagram 31
- AL600ULX 34
- 2.2.3 AC Indicator 35
- 2.4 Alarm Input Wiring 37
- 2.7 Weatherproofing 40
- 2.8 Relay Contact Protection 41
- 2.8.1 DC Inductive Load 42
- 2.8.2 AC Inductive Loads 42
- System Testing 43
- 4 Maintenance 45
- 4.2 AES/Extended Firmware 46
- 5 UL Certified Installations 47
- 5.1 Power 49
- 5.2.1 Acknowledgement Signal 52
- 5.3 UL Requirements 52
- 5.4 Troubleshooting 54
- LNL-500 57
- 6 Overview of the LNL-500 59
- 2.00 (50.8)2.00 (50.8) 60
- 7 Installation 61
- (Maximum of 8 control panels) 64
- 7.1.4 Power 66
- 7.1.5 Other 66
- 8 Configuration 67
- 8.1.3 Communication Baud Rate 68
- 8.2 Installing Jumpers 69
- 9 Maintenance 70
- 10 Specifications 71
- LNL-1000 73
- 11 Overview of the LNL-1000 75
- 11.2 The ISC Board 76
- 12 Installation 77
- Ports 2 - 5 81
- 12.1.4 Power 83
- 12.1.5 Other 83
- 13 Configuration 84
- 14 Maintenance 89
- 15 Specifications 90
- LNL-2000 91
- 16 Overview of the LNL-2000 93
- 16.2 The LNL-2000 Board 94
- 17 Installation 95
- RS-232 Communications 96
- RS-485 Communications 96
- RS-485 Line Termination 96
- RS-485 Communication Wiring 100
- 17.1.4 Power 101
- 17.1.5 Other 101
- 18 Configuration 102
- 18.1.2 Hardware Flow Control 103
- 18.2 Installing Jumpers 105
- 4.00 (101.60) 106
- 3.00 (76.20) 106
- 18.2.5 Baud Rate Default 107
- Input/Output 108
- Control Module(s) 108
- 19 Maintenance 109
- 20 Specifications 110
- LNL-2210 111
- INTELLIGENT 111
- SINGLE DOOR 111
- CONTROLLER 111
- 21 Overview of the LNL-2210 113
- The LNL-2210 Board 114
- 22 Installation 115
- 22.1.1 Communication Wiring 116
- 22.1.2 Reader Wiring 116
- 22.1.3 Input Circuit Wiring 117
- 22.1.4 Relay Circuit Wiring 118
- 22.1.5 Power 119
- 22.2 Memory Backup Battery 119
- 22.3 Installing Jumpers 120
- 22.4 Setting Dip Switches 120
- 22.4.1 Default Settings 120
- 22.6 Embedded Web Server 121
- 88158404 124
- 23 Maintenance 126
- 24 Specifications 127
- - RoHS compliant 128
- LNL-2220 129
- DUAL READER 129
- 25 Overview of the LNL-2220 131
- 25.2 The IDRC Board 132
- 25.3 Default Settings 133
- 26 Installation 134
- 26.2 Communication Wiring 136
- 26.3 Reader Wiring 137
- 26.3.2 Command Keypad 138
- 26.3.3 Bioscrypt Readers 139
- 26.4 Input Circuit Wiring 139
- 26.5 Relay Circuit Wiring 140
- 26.5.1 Power and Alarm Inputs 141
- 26.6 Memory Backup Battery 142
- 26.7 Configuration 142
- 26.7.1 Setting Dip Switches 142
- 26.7.2 Installing Jumpers 143
- 26.9 Embedded Web Server 144
- 27 Maintenance 147
- 28 Specifications 149
- LNL-3300 151
- 29 Overview of the LNL-3300 153
- 29.3 Default Settings 154
- 30 Installation 155
- 30.2 Power and Alarm Inputs 156
- 30.3 Memory Backup Battery 156
- 30.4 Configuration 156
- 30.4.1 Setting DIP Switches 156
- 30.4.2 Installing Jumpers 157
- 30.6 Embedded Web Server 159
- 31 Maintenance 162
- Run time: 163
- 32 Specifications 164
- COMMUNICATIONS 165
- 33 ISC Communication 167
- ISC Communications 168
- 33.2.3 Configuring the ETHLAN 170
- 33.3.1 ETHLAN-MICR Standoffs 172
- STANDOFFS 173
- Standoffs for ETHLAN 173
- LITE to ISC 173
- 33.4.2 Security Enhancements 177
- 33.4.3 Firmware 177
- 33.4.5 Removal of Reset Pin 179
- 33.6 Lantronix CoBox-DR 184
- Lantronix 186
- Ports 1 & 6 Wiring 186
- Configuration 186
- Using Telnet 188
- Using a Terminal Program 190
- Wiring for RS-232 4-wire 193
- Unit Setup (RS-232 4-wire) 195
- Wiring for RS-485 2-wire 195
- 33.9 Commonly Used Values 197
- Common I/F Mode Values 197
- Common Flow Control Values 197
- 33.12.2 Wiring 200
- Black Box LD485A 201
- 33.12.4 Wiring 202
- 12345678 206
- 33.15 KBC Fiber Optic Modem 209
- RocketPort 4 Port 212
- Serial Hub Si 212
- Jumper Settings 213
- 33.16.3 RocketPort Driver 214
- DIP Switch Settings 214
- Configure Ports 215
- LNL-1100 INPUT 217
- CONTROL 217
- 34 Overview of the LNL-1100 219
- 34.2.1 Status LEDs 220
- 34.2.2 Series 1 and Series 2 221
- Input Control Module 221
- 35 Installation 222
- 15K – 223
- 35.1.4 Relay Outputs 224
- 35.1.5 Power 225
- 35.2 Elevator Control 226
- 36 Configuration 227
- LNL-1100 Input Control Module 228
- 36.2 Installing Jumpers 230
- Intelligent System Controller 231
- 32 Downstream 231
- 37 Specifications 232
- LNL-1100-U INPUT 233
- 38.1 Package Contents 235
- 39 Installation 236
- 40 Configuration 237
- 40.1.2 Device Address (SW2) 238
- 40.2 Installing Jumpers 239
- 40.3 Status LEDs 240
- 41 Mounting 242
- 42 Wiring 244
- 15K - 245
- 42.4 Control Output Wiring 247
- 42.4.1 Relay Outputs 248
- 42.5 Elevator Control 248
- 42.6 Power and Communications 249
- 42.7 UL Listed Installations 250
- 43 Specifications 251
- LNL-1200 OUTPUT 253
- 44 Overview of the LNL-1200 255
- Output Control Module 256
- 44.2.1 Status LEDs 257
- 44.2.2 Series 1 and Series 2 257
- 45 Installation 258
- 45.1.3 Relay Outputs 259
- 45.1.4 Power 260
- 45.2 Elevator Control 260
- 46 Configuration 262
- 46.2 Installing Jumpers 265
- 47 Specifications 267
- LNL-1200-U 269
- OUTPUT CONTROL 269
- 48.1 Package Contents 271
- 49 Installation 272
- 50 Configuration 273
- 50.1.2 Device Address (SW2) 274
- 50.2 Installing Jumpers 275
- 50.3 Status LEDs 276
- 51 Mounting 279
- 52 Wiring 281
- 52.2 Upstream Communication 282
- 52.3 Relay Outputs 282
- 52.4 Elevator Control 284
- 52.5 Power and Communications 285
- 52.6 UL Listed Installations 286
- 53 Specifications 287
- LNL-1300 SINGLE 289
- INTERFACE 289
- 54 Overview of the LNL-1300 291
- 54.2.1 Status LEDs 292
- 54.2.2 Series 1 and Series 2 293
- 55 Installation 294
- 55.1.2 Upstream Communication 295
- 55.1.3 Relay Outputs 296
- AC STRIKE 297
- 55.1.6 Power 298
- 55.2 Elevator Control 299
- Overview of Elevator Control 300
- 56 Configuration 301
- 56.1.1 Device Address 302
- 56.1.4 Cabinet Tamper 303
- 56.1.5 EOL Termination 304
- 57 Specifications 305
- LNL-1300-U 307
- 58.1 Package Contents 309
- 59 Installation 310
- 60 Configuration 311
- 60.1.2 Device Address (SW2) 312
- 60.2 Installing Jumpers 313
- 60.3 Status LEDs 314
- 61 Mounting 317
- 62 Wiring 319
- 62.3 Relay Outputs 321
- Relay Contact (AC Strike) 322
- SDC AUX relay wiring 322
- 62.6 Elevator Control 324
- 62.8 Power and Communications 325
- 62.9 UL Listed Installations 326
- 63 Specifications 327
- LNL-1320 DUAL 329
- 64 Overview of the LNL-1320 331
- LEDs and six (6) relay LEDs 332
- 64.2.1 Status LEDs 333
- 64.2.2 Series 1 and Series 2 334
- Dual Reader Interface Module 334
- 65 Installation 335
- 65.1.2 Upstream Communication 337
- 65.1.3 Control Output Wiring 338
- DRI Alarm Output Contact Wiri 339
- Monitors 340
- 65.1.7 Power 341
- 65.2 Elevator Control 342
- 66.1 Setting DIP Switches 344
- 66.1.1 Device Address 344
- 66.2 Installing Jumpers 347
- 67 Specifications 348
- LNL-1320-U DUAL 349
- 68.1 Package Contents 351
- 69 Installation 352
- 70.1 Setting DIP Switches 353
- 70.1.2 Device Address (SW2) 354
- 70.2 Installing Jumpers 356
- 70.3 Status LEDs 357
- 71 Mounting 361
- 72 Wiring 363
- 72.2 Upstream Communication 364
- 72.3 Control Output Wiring 365
- 72.3.1 Relay Outputs 365
- Relay contact (AC strike) 366
- DDC AUX relay wiring 366
- LCD reader display control 367
- 72.7 Power and Communications 368
- 72.8 UL Listed Installations 369
- 73 Specifications 370
- LNL-8000 STAR 373
- MULTIPLEXER 373
- 74.1 Interfaces 375
- 74.2.1 Status LEDs 376
- 75 Installation 377
- 75.1.3 Power 378
- 75.2 Wiring and Termination 379
- 5 4 3 2 380
- 76.1 Setting DIP Switches 381
- 76.2 Installing Jumpers 382
- 77 Specifications 383
- LNL-8000 Star Multiplexer 384
- LNL-2005W 385
- MAGNETIC CARD 385
- ACCESS READER 385
- 78 Overview 387
- 79.1 Wiring 388
- 79.2 Mounting the Reader 388
- KEYPAD CONNECTOR 389
- DIELECTRIC 389
- SWITCH SLIDE 389
- RJ-11 JACK 389
- 80 Configuration 390
- 80.3 Grounding the Reader 391
- 80.4 Reader Verification 391
- 80.5 Status LEDs 391
- 80.6 Maintenance 391
- 80.7 Product Identification 392
- 81 Specifications 393
- Optional Wall Plate, WP-10 394
- WALL STUD 395
- 81.2 Reader Weather Shield 396
- LNL-2010W/2020W/ 397
- 2020W-NDK/NDKV2 397
- 82 Overview 399
- 83.1 Wiring 400
- 83.2 Mounting the Reader 400
- SLIDE ENGAGED 401
- SLIDE DISENGAGED 401
- 84 Configuration 403
- Switch/Jumper Position 404
- 84.4 TTL Interface 405
- 84.4.1 Use with a WRI Reader 405
- 84.5 Grounding the Reader 406
- 84.6 Reader Verification 406
- 84.7 Status Indicators 406
- 84.8 Maintenance 407
- 84.9 Product Identification 407
- 85 Specifications 408
- 85.2 Reader Weather Shield 411
- LENELPROX 413
- 86.1 Read Range 415
- 86.2 Installation Guidelines 415
- 86.2.2 Power 416
- 86.2.3 Grounding 416
- 86.2.4 Wiring 417
- 86.3 LenelProx LPMM-6800 417
- 86.3.1 Installation 417
- READER INTERFACE 418
- 86.3.2 Specifications 419
- 86.4 LenelProx LPSP-6820 419
- 86.4.1 Installation 419
- LenelProx LPSP-6820 420
- 86.4.2 Specifications 422
- 86.5.1 Installation 422
- Reader 1 424
- 86.5.2 Operating Modes 425
- 86.5.3 Specifications 425
- 86.5.4 Notes 425
- 86.6 LenelProx LPSR-2400 426
- 86.6.1 Installation 426
- LenelProx Readers 428
- 86.6.2 Specifications 429
- 86.7 LenelProx LPRKP-4600 429
- 86.7.1 Installation 429
- 86.7.2 Specifications 432
- 86.8.1 Installation 433
- 86.8.2 Maximum Read Range 436
- Metal Compensation 437
- Distance between Readers 437
- Credentials 437
- Environment 437
- Field Test 437
- 86.8.3 Specifications 438
- 86.9 LenelProx LPLR-911 439
- Wiring Requirements 440
- Power Supply 440
- Grounding 440
- Measuring Reader Distance 440
- 86.9.2 Installation 441
- 86.9.4 Specifications 445
- LENEL KEYPADS 447
- 87 Lenel Keypads 449
- 87.1.1 Wiring the LNL-1300 450
- 87.1.2 Wiring the LNL-1320 451
- 87.2 Reader Specifications 451
- Lenel Keypads 452
- LENEL OPENCARD 453
- 88.1 OpenCard ISO-X Readers 455
- 88.1.1 Wiring the LNL-1300 456
- 88.1.2 Wiring the LNL-1320 457
- 88.2 OpenCard XF1550/XF1560 457
- 88.2.1 Wiring the LNL-1300 458
- 88.2.2 Wiring the LNL-1320 459
- 88.3 Specifications 459
- LNL-500B 461
- BIOMETRIC 461
- 89.1 Interfaces 463
- The LNL-500B Board 464
- 90.1 Wiring 465
- 90.1.3 Power 467
- Ports 2 - 3 468
- 91.1 Setting DIP Switches 470
- 91.1.1 Interface Address 470
- 91.1.3 Downstream Baud Rate 472
- 91.2 Installing Jumpers 472
- 92.1 Verification 473
- 92.2 Memory Backup Battery 473
- 92.3 Firmware 473
- 94 Specifications 475
- HANDKEY 477
- 95.1.1 Diagnostic Mode 479
- 95.1.2 HandKey Enrollment 480
- HandKey Readers 482
- HandKey ID3D-R 483
- Back of RSI Handkey unit 486
- 95.1.4 Signal Ground 487
- 95.1.5 Power 488
- 95.1.6 Communication 488
- Resetting the HandKey Reader 490
- 95.2.1 Encoding 493
- Card Format 494
- Back of RSI MIFARE HandKey 495
- BIOCENTRIC 499
- SOLUTIONS 499
- 96.1 Interfaces 501
- 97 Enrollment Readers 502
- Philips Electronics Standard 503
- HID Corp 503
- 97.3 Encoding Smart Cards 504
- 98 Verification Readers 505
- Biocentric Solutions 506
- Configuration tab 507
- Power Up Sequence 507
- Standard Operation 507
- Button Operation 507
- Normal Error Conditions 508
- Abnormal Error Conditions 509
- 99.1 Tips and Tricks 511
- 99.1.3 Fingerprint Pressure 513
- 99.1.4 Trade-offs 514
- 99.1.5 Specifications 514
- GuardDog 515
- BIOSCRYPT 517
- 100 Overview 519
- Bioscrypt Readers 520
- 101.2 Enrollment Readers 523
- 101.2.1 Reader Configuration 524
- 101.2.2 Firmware 524
- 101.3 V-Pass FX 525
- 00010203 526
- 04050607 526
- 101.3.1 Termination 528
- 101.4 V-StationA 529
- 101.5 V-Smart 534
- 101.5.2 LED Settings 536
- 101.5.3 Smart Card Settings 538
- Indicator Light 547
- Back of V-Station Unit 548
- Dual Reader 548
- Interface Module 548
- 101.6.2 Encoding Smart Cards 553
- 101.7 PIV-Station 554
- 101.7.1 PIV-Station Wiring 554
- 12-24 VDC 555
- 101.8.1 4G Registration 556
- 101.8.2 4G Configuration 556
- SCHLAGE 563
- WIRELESS 563
- 102.1 Interfaces 565
- 103.1 Wiring 566
- 103.1.3 Power 568
- Termination 569
- 104.1 Setting DIP Switches 570
- 104.1.1 Interface Address 570
- 104.1.3 Downstream Baud Rate 572
- 104.2 Installing Jumpers 572
- 104.3 Firmware 572
- 105.1 PIM-485-16-OTD 573
- 105.3 PIM-OTD 574
- Single Reader 575
- Schlage Wireless Readers 576
- 106.1 Use with the LNL-2020W 577
- 106.2 OnGuard Configuration 577
- 106.2.1 Strike Time 577
- 107 Specifications 579
- WIRELESS LOCKS 581
- 108.1 Interfaces 583
- 109.1 Wiring 584
- 109.1.3 Power 586
- 110.1 Setting DIP Switches 588
- 110.1.1 Interface Address 588
- 110.1.3 Downstream Baud Rate 590
- 110.2 Installing Jumpers 590
- 110.3 Firmware 590
- 111.1 PIM400-485 591
- Addresses 591
- 2. On the HHD, log onto SUS 592
- 111.3 AD-400 Wireless Locks 593
- 111.4 Handheld Device (HHD) 594
- Schlage Wireless Locks 596
- Link 2 Button (S3) 597
- Link 1 Button (S2) 597
- 112 Wiring and Setup 600
- LNL-500W 602
- Wireless Reader Gateway 602
- 113.1 OnGuard Configuration 603
- 113.1.1 Strike Time 603
- • Request-to-Enter 604
- 114 Specifications 605
- COMMAND 607
- 115.1 Communication 609
- Command 610
- 115.1.2 Wiring the LNL-CK 613
- Command Keypad Power 614
- Command Keypad Communication 614
- 115.1.3 DIP Switches 616
- 115.1.4 Jumpers 616
- 115.1.5 LNL-CK Configuration 616
- 115.1.6 Status Display 617
- 115.1.7 OnGuard Configuration 617
- 115.1.8 Command Programming 618
- Alarm Mask Groups 619
- Command Keypad 620
- 115.2 Specifications 621
Related products and manuals for Security door controllers Samsung Series r5+ 590
(35 pages)© 2020, manymanuals.com. All rights reserved. | 3.666 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals