Samsung iDCS 500 User's Guide Page 106
- Page / 130
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
iDCS 500 INSTALLATION
TECHNICAL MANUAL PART 7 NOVEMBER 2001
7.3
Use one pair twisted #24 AWG or #26 AWG jumper wire to cross-connect SLI circuits
to the VM/AA system (see Figure 7–7). For more information on programming these
ports, see the Programming Section, MMCs 207, 601 and 726
. See also the Standard
Telephone User Guide for feature codes and instructions.
7.8 CONNECTING SYSTEM BACKUP BATTERIES TO
THE iDCS 500 POWER SUPPLY
The iDCS 500 power supplies (PSU-B and PSU60) contain a monitoring circuit to
switch the system to customer provided 48VDC batteries when AC power is
interrupted. Calls in progress are not disconnected. The power supply circuitry
monitors and recharges batteries as needed.
Connect four 12V batteries or eight 6V batteries in series. Any NICAD or lead acid (car
or motorcycle type) battery can be used if its rating is not less than 6AH (amp hours)
but no more than 40AH per power supply. The batteries must be located within three
feet of the KSU. Use the factory-supplied wire harness with 36” white and black leads
to connect batteries (see Figure 7-8).
Observe the following precautions when installing batteries:
a. Make sure the batteries you install conform to local building, fire and safety codes.
Some battery types emit hydrogen gas during the charging state and may require
venting to fresh air.
b. Do not place batteries directly on a concrete floor. This causes them to discharge
very quickly.
c. Follow the battery manufacturer’s recommended installation and maintenance
procedures.
- INSTALLATION SECTION 1
- 4 POWER UP PROCEDURES 2
- 5 CONNECTING TELCO CIRCUITS 2
- 10 ADDING CARDS TO THE SYSTEM 4
- 11 CADENCE SET UP 4
- PART 1. SITE REQUIREMENTS 5
- FIGURE 1–1 6
- 2.1 UNPACKING AND INSPECTION 7
- FLOOR MOUNT 7
- 2.7 GROUNDING 11
- 2.8 POWER CONNECTIONS 13
- 2.9 MDF CABLING 14
- FIGURE 2–1 15
- FIGURE 2–2 16
- FIGURE 2–3 17
- FIGURE 2–4 18
- FIGURE 2–5 19
- FIGURE 2–6 20
- FIGURE 2–7 21
- FIGURE 2–8 22
- FIGURE 2–9 23
- 3.1 MCP 24
- (see Figure 3–2) 24
- DIP SWITCH USE 27
- iDCS 500 MCP 27
- 3.3 LCP CARD 29
- (see Figure 3–4) 29
- 3.7 MISC BOARD 31
- (see Figure 3-10) 31
- 3.8 SCM BOARD 31
- (see Figure 3-12) 31
- 3.23 16SLI CARD 35
- (see Figure 3–19) 35
- 3.24 BRI CARD 35
- 3.25 8MWSLI CARD 36
- 3.26 16MWSLI CARD 36
- 3.27 TEPRI CARD 37
- (see Figure 3–20) 37
- TEPRI CARD DIP SWITCH 37
- DTPRI LED DEFINITIONS 38
- 3.28 AUTO ATTENDANT CARD 38
- (see Figure 3–21) 38
- 3.29 CADENCE 38
- (see Figure 3–22) 38
- (see Figure 3–23) 39
- 3.31 E911 CARD 39
- (see Figure 3–24) 39
- FIGURE 3–1 41
- FIGURE 3–2 42
- FIGURE 3–3 43
- FIGURE 3–4 44
- FIGURE 3–5 45
- FIGURE 3–6 46
- FIGURE 3–7 47
- FIGURE 3–8 48
- FIGURE 3–9 49
- FIGURE 3–10 50
- FIGURE 3–11 51
- FIGURE 3–12 52
- FIGURE 3–13 53
- FIGURE 3–14 54
- FIGURE 3–15 55
- FIGURE 3–16 56
- FIGURE 3–17 57
- FIGURE 3–18 58
- FIGURE 3–19 59
- FIGURE 3–20 60
- FIGURE 3–21 61
- FIGURE 3–22 62
- FIGURE 3–23 63
- FIGURE 3–24 64
- PART 4. POWER UP PROCEDURES 65
- 4.4 PCB VERIFICATION 67
- FIGURE 4–1 69
- ORDERING A T1 71
- FIGURE 5–1 72
- FIGURE 5–2 73
- FIGURE 5–3 74
- FIGURE 5–4 75
- FIGURE 5–5 76
- FIGURE 5–6 77
- FIGURE 5–7 78
- FIGURE 5–8A 79
- FIGURE 5–8B 80
- 6.1 SAFETY PRECAUTIONS 81
- 6.2 KEYSETS 81
- 6.4 SINGLE LINE TELEPHONES 82
- 6.6A WALL-MOUNTING KEYSETS 82
- FIGURE 6–1a 85
- FIGURE 6–1b 86
- FIGURE 6–2a 87
- FIGURE 6–2b 88
- FIGURE 6–3a 89
- FIGURE 6–3b 90
- FIGURE 6–3c 91
- FIGURE 6–3d 92
- FIGURE 6–3e 93
- FIGURE 6–4a 94
- FIGURE 6–4b 95
- FIGURE 6–5 96
- FIGURE 6–6 97
- FIGURE 6–6a 98
- FIGURE 6–7 99
- FIGURE 6-7 100
- FIGURE 6–8 100
- FIGURE 6–9 101
- FIGURE 6–10 102
- FIGURE 6–11 103
- 7.2 EXTERNAL PAGING 104
- 7.3 COMMON BELL 104
- 7.6 PC PROGRAMMING 105
- 7.4 RING OVER PAGE 105
- THE iDCS 500 POWER SUPPLY 106
- FIGURE 7–1 107
- FIGURE 7–2 108
- FIGURE 7–3 109
- FIGURE 7–4 110
- FIGURE 7–6 111
- FIGURE 7–5 111
- FIGURE 7–7 112
- FIGURE 7–8 113
- PART 8. INSTALLING KEYSET 114
- DAUGHTERBOARDS 114
- 8.5 KDB-SLI 115
- 8.6 CONNECTING TO THE KDBS 115
- FIGURE 8–1 116
- FIGURE 8–2 117
- FIGURE 8–3 118
- FIGURE 8–4 119
- FIGURE 8–5 120
- FIGURE 8–6 121
- FIGURE 8–8 122
- FIGURE 8–7 122
- FIGURE 8–9 123
- MANAGEMENT 124
- FIGURE 10–1 127
- LED INDICATIONS 128
- RESET BUTTON 128
- POWER REQUIREMENTS 128
- 11.3 TESTING THE HARDWARE 130
Related products and manuals for Telephones Samsung iDCS 500
Telephones Samsung DCS-816 User Manual
(28 pages)
(28 pages)
Telephones Samsung iDCS 500 User's Guide
(189 pages)
(189 pages)
Telephones Samsung SMT-3105 User Manual
(4 pages)
(4 pages)
Telephones Samsung OfficeServ iDCS User Manual
(100 pages)
(100 pages)
Telephones Samsung SGH-P510RSA User Manual
(210 pages)
(210 pages)
Telephones Samsung SMT-W5100E User's Guide
(125 pages)
(125 pages)
Telephones Samsung SF505 Specifications
(52 pages)
(52 pages)
Telephones Samsung SF-360 Series User Manual
(78 pages)
(78 pages)
Telephones Samsung SGHT309 User's Guide
(198 pages)
(198 pages)
Telephones Samsung SGH-X100T User Manual
(41 pages)
(41 pages)
Telephones Samsung SMT-3105 User's Guide
(49 pages)
(49 pages)
Telephones Samsung 7200 User Manual
(180 pages)
(180 pages)
Telephones Samsung HX-DU075DB User Manual
(55 pages)
(55 pages)
Telephones Samsung Falcon User's Guide
(44 pages)
(44 pages)
Telephones Samsung SMT-i5243 User's Guide
(96 pages)
(96 pages)
© 2020, manymanuals.com. All rights reserved. | 2.803 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals