Samsung WF410ANR User Manual download pdf

Fast Track Troubleshooting

Model:

WF410ANR/XAA

WF410ANW/XAA

Publication # nwWF410 Revision Date 06/17/2013

Quick Test Mode:

Note: This test erases all faults and memory:

To enter press Soil, Signal, & Power

simultaneously with the power off.

1. All LED’s light up and the washer beeps

as it enters the Quick Test Mode.

2. The unit displays the software version for a

second then clears the EEprom.

3. After the displaying the software version, LCD

will display Model information. If EEEE is displayed

the PCB ass’y is defective.

4. When the version is displayed, turn the Jog-Dial

CCW until version disappears. Press the following

keys to test the various components

Press Temp Key (Lock door with Spin key) to cycle

through the Water Valves circuit test in this order: Cold

Main, Bleach, Hot, Boot valve then off.

Press Spin Key to test Door Lock/Unlock circuit.

Press Signal Key to test Drain Pump

Press Soil Key to test Water Heater

Service Mode:

This mode allows more detailed operation tests and trouble-

shooting, to enter press Signal & Extra Rinse

simultaneously with the power on.

While in Service Mode the following tests can be performed:

Quick Spin Test = Delay Start & Pure Cycle: This accel-

erates the drum motor from 0 to maximum RPM over a few

minutes. Note: Stay with the washer during this test, out of

balance detection may be bypassed. Press the Start/Pause

button during the test to hold its spinning speed for 10 minutes

before going back to Quick Spin Test Mode.

Cycle Count = Press the Signal button to see how many

times the unit was used.

Soft Ware # = Press the Soil button to see the software version

Fault Code Test = Press the Extra Rinse button to view the

stored fault codes – then turn Jog Dial to view error codes

(Push Start/Pause while the code is displayed to view the num-

ber of cycles since the error occurred)

Peripheral (Main PCB) input Tests

1. Press Pure Cycle

. Then turn the Jog-Dial so that the Extra

Rinse LED is turned on. Next, press the Start/Pause Key. The

Water Temperature will be displayed in Fahrenheit.

2. Press Pure Cycle

. Then turn the Jog-Dial so that the Extra

Spin LED is turned on. Next, press the Start/Pause Key. The

door status will be displayed (OP if open, CL if closed).

3. Press Pure Cycle

. Then turn the Jog-Dial so that the Delay

Start LED is turned on. Next, press the Start/Pause Key. The

door lock Switch status will be displayed (UL if unlocked, Lo if

locked).

4. Press Pure Cycle

. Then turn the Jog-Dial so that the Pure

Cycle LED is turned on. Next, press the Start/Pause Key. The

Water Frequency will be displayed.

IMPORTANT SAFETY NOTICE – “For Technicians Only” This service data sheet is

intended for use by persons having electrical, electronic, and mechanical experience

and knowledge at a level generally considered acceptable in the appliance repair trade.

Any attempt to repair a major appliance may result in personal injury and property

damage. The manufacturer or seller cannot be responsible, nor assume any liability for

injury or damage of any kind arising from the use of this data sheet.

EEPROM Clear Check

Power off, Press Delay Start, Signal and Power Key at

the same time. Good = Good Fail = FAIL

All memory will be cleared, including Fault Codes

This should be done when a new Main PCB is installed

Fabric Softener Dispenser Test:

Start Rinse and Spin Cycle. After fill is completed

remove detergent drawer, place towel below opening

and within 3 minutes the dispenser will activate

NOTICE

The WF410 incorporate parts

changes in the motor circuit, main

PCB and wiring harness. You can

determine which parts are re-

quired by inspecting label inside

the door. If the version number is

not listed, it is the original design.

Version 01 Parts Changed

ASSEMBLY BLDC MOTOR,

ASSEMBLY PCB MAIN, AS-

SEMBLY M.WIRE HARNESS

SUPPORT INFORMATION

Training — Plus One http://my.plus1solutions.net/clientPortals/samsung/

Help — GSPN http://service.samsungportal.com/

1 2 3 4 5 6 7

Summary of Contents

Page 1 - Fast Track Troubleshooting

Fast Track Troubleshooting Model: WF410ANR/XAA WF410ANW/XAA Publication # nwWF410 Revision Date 06/17/2013 Quick Test Mode:

Page 2 - Boot Valve

WF410 CN3 CN4 CN7 CN8 CN6 CN5 RY2 RY1 CN2 Gray Gray CN1 Boot Valve

Page 3

Washer Connector Checks WF410 CN3 1 Door Lock Close (Blk) 2 Door Lock Open (Wht) 3 Drain Pump (Vio) 4 Boot Valve (Red) 5 Bleach Valve (Pnk)

Page 4

Door Lock Check Test 1 Test 2 Connector CN2 Pin 3 (Brown) and CN3 Pin 1 (Black) When Door is Locked or Unlocked there is a pulse of 120VAC for a few

Page 5

Error Type Error Mode Details LED LCD Drain Error nD 1 Chec

Page 6

Foot Pad for Walking Washer, There is one in each package, so order 4 Error Type Error Mode Details LED LCD Heater Er

Page 7

Water valve connections for the Detergent Drawer Laundry Touch Up Paints Stacking Kit : (Model No : SK-3A1/XAA, SK-4A/XAA, SK-5A/XAA) Samsung washe

Comments to this Manuals

No comments

Samsung WF410ANR User Manual

Browse online or download User Manual for Washing machines Samsung WF410ANR. Fast Track Troubleshooting

Summary of Contents

Comments to this Manuals

Related products and manuals for Washing machines Samsung WF410ANR