Samsung GN642FFXD User Manual download pdf (Page 12)

1. Remove the pan support, the burner lid and

ﬂame spreader and carefully turn the

appliance upside down and place it on a

cushioned mat.

Take care that the Ignition devices and ﬂame

supervision devices are not damaged in this

operation.

2. Apply the sealing strip provided around the

edge of the appliance.

3. Do not leave a gap in the sealing agent or

overlap the thickness.

Do not use a silicon sealant to seal the

appliance against the aperture.

This will make it difﬁcult to remove the

appliance from the aperture in future,

particularly if it needs to be serviced.

1. Place the bracket(B) over the holes that match the size

of the screws.There are one set of screw holes in each

corner of the hob(H).

Slightly tighten a screw(C) through the bracket(B) so

that the bracket is attached to the hob, but so that you

can still adjust the position it.

2. Carefully turn the hob back over and then gently lower it

into the aperture hole that you have cut out.

3. On the underneath of the hob, adjust the brackets into a

position that is suitable for your worktop.

Then fully tighten the screws(C) to secure the hob into

position.

(A) SEALING STRIP

Installing the appliance

■ This appliance must be installed and connected in accordance with installa-

tion regulations in force in the country in which the appliance is to be used.

■ This appliance is supplied to run on natural gas only and cannot be used on

any other type of gas without modiﬁcation.

Conversion for use on LPG and other gases must only be undertaken by a

qualiﬁed person.

■ Connection with a rigid pipe made from copper and with

screw-on mechanical connectors.

Make the connection directly to the end of the elbow ﬁtted on

the appliance.

■ Connection using ﬂexible undulated metal tube with

screw-on connectors. (Fig. A)

You can use a ﬂexible stainless steel pipe available from your

after sales service department.

■

Connection using ﬂexible tube with screw-on connectors.

(Fig.B)

These tubes must not exceed 2 meters in length and must be

accessible along their entire length.

■ A full operational test and a test for possible leakages must be carried out

by the ﬁtter after installation. (such as soap water or gas detector)

■ Access to the whole length of the connection hose must be possible and

the gas hose must be replaced before its use before the end of service life

(indicated on the hose)

Gas Connection

Elbow

The gas inlet connection ﬁtting is 1/2 inch female thread.

Gas distributed by pipe ; natural gas, propane-air gas or butane-air gas

For your safety, you must choose from the three following connection option.

■ For the user’s safety, we advise the connection to be made

with a rigid pipe if this is possible, using a ﬂexible undulated

metal tube with scerw-on connectors (maximum length

2meters) (Fig.A)

■ For an existing installation, where it is not possible to ﬁt a

reinforced, braided, ﬂexible gas hose, the connection can be

made with a ﬂexible gas hose (maximum length 2meters),

with two clamps.

One on the connector, and the other on the pressure

regulator, and a gasket should be ﬁtted between the

connector and the hob’s elbow. (Fig.B)

Elbow

Gas supplied by tank or cylinder (butane/propane)

■

You can obtain the connector and the gasket from your After-Sales Service.

In France, you must use a tube or a pipe featuring the “NF Gaz” logo.

If the installation is difﬁcult, unscrew the Elbow slightly and tighten it after

locating the Elbow.

Fig.A Fig.B

Gasket

Connector

Clamp

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 41 42

Comments to this Manuals

No comments

Samsung GN642FFXD User Manual Page 12

Comments to this Manuals

Related products and manuals for Unknown Samsung GN642FFXD